(1)
Put an access platform in position at the zone 232.
(2)
Open the forward cargo-compartment door 825 (Ref. TASK 52-30-00-860-001).
Subtask 53-21-00-010-057
B. Removal of the Components
(1)
Disconnect the actuator from the door structure (Ref. TASK 52-36-18-000-001).
(2)
Remove the access panel 232PF (Ref. TASK 53-22-12-000-001).
EFF : ALL 53-21-00Page A619
May 01/05
R
CES Subtask 53-21-00-110-061
C. Preparation of the Inspection Area
(Ref. Fig. 622/TASK 53-21-00-991-040)
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THIS/THESE
_______ MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
(1)
Clean the inspection area with CLEANING AGENTS (Material No. 11-004) and lint-free cotton cloth MISCELLANEOUS (Material No. 19-003), if necessary.
(2)
Make sure that the surface of the inspection area is clean and smooth.
(3)
Do a visual check of the inspection area for damage or
discontinuities.
(4)
Make sure that there is no:
(a)
Corrosion damage:
-If you find corrosion damage, refer to the Structural Repair Manual (Ref. SRM 512200,P.Block 001) for types of corrosion, inspection, removal and corrosion protection.
(b)
Other damage (cracks, scratches, stress, marks, dents, bumps...):
-If you find this type of damage, refer to the Structural Repair Manual (Ref. SRM 511100,P.Block 001) for damage classification and corrective action.
EFF : ALL 53-21-00Page A620
May 01/05
R
CES
Cross Beams at FR25, FR26 and FR27 Figure 622/TASK 53-21-00-991-040
R EFF : ALL 53-21-00 Page A621 May 01/05
CES
4. Procedure
_________ Subtask 53-21-00-250-051
A. Inspection
(Ref. Fig. 622/TASK 53-21-00-991-040)
(1)
Do a special detailed inspection of the structure above the forward cargo-compartment door. This inspection is applicable to the inside radius of the cross-beam on the fittings at FR25, FR26 and FR27 (Ref. NTM 532140,P.Block-601).
(2)
Make a report of the damage after the NDT inspection:
(a)
Corrosion damage:
-If you find corrosion damage, refer to the Structural Repair Manual (Ref. SRM 512200,P.Block 001) for types of corrosion, inspection, removal and corrosion protection.
(b)
Other damage (cracks, scratches, stress, marks, dents, bumps...):
-If you find this type of damage, refer to the Structural Repair Manual (Ref. SRM 511100,P.Block 001) for damage classification and corrective action.
5. Close-up
________ Subtask 53-21-00-410-057
A. Installation of the Components
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the access panel 232PF (Ref. TASK 53-22-12-400-001).
(3)
Connect the actuator to the door structure (Ref. TASK 52-36-18-400-001).
Subtask 53-21-00-942-074
B. Close Access WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE ELEVATORS ARE CLEAR
_______
DURING CARGO COMPARTMENT DOOR OPERATION.
(1)
Close the forward cargo-compartment door 825 (Ref. TASK 52-30-00-860-002).
(2)
Remove the access platform(s).
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
TASK 53-21-00-210-001
General Visual Inspection of Cabin Floor Structure, Excluding Areas below
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身2(8)
