(Ref. Fig. 401A/TASK 53-22-14-991-001)
**ON A/C 151-199,
(Ref. Fig. 401B/TASK 53-22-14-991-001-A)
**ON A/C 301-399,
(Ref. Fig. 401C/TASK 53-22-14-991-001-C) R **ON A/C 401-499,
R (Ref. Fig. 401D/TASK 53-22-14-991-001-D) **ON A/C ALL
Subtask 53-22-14-916-050
A. Preparation for Installation:
(1) Remove the old sealant from the floor panels with a nonmetallic scraper.
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
EFF : ALL
53-22-14Page 411
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE
_______
SPECIAL MATERIAL.
THIS MATERIAL IS DANGEROUS.
(2)
Clean the component interface and the adjacent area with CLEANING AGENTS (Material No. 11-003) and lint free cloth.
(3)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(4) Do an inspection of the component interface and/or the adjacent area. R **ON A/C 001-049, 051-099, 101-101, 106-149, 201-299, 301-399, 401-499,
Subtask 53-22-14-420-050-A
B. Installation of the Floor Panels:
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Put the floor panels (1) and the seals (3) and (6) in position.
(3)
Apply SPECIAL MATERIALS (Material No. 05-002) to the screws (2).
(4)
Install the screws (2) and TORQUE to 0.42 m.daN (37.16 lbf.in).
(5)
Install the cord (7) FIBER GLASS CORD 1.1MM DIA. (DAN107-1) in the gap between the floor panels (1).
NOTE : Make a loop at the end of the cord, this will help the next
____
removal procedure.
(6) Apply SEALANTS (Material No. 09-005) in the gap between the floor panels (1) and the cutouts of the tiedown positions.
EFF : ALL
53-22-14Page 412
**ON A/C 102-105, 151-199,
Subtask 53-22-14-420-050
B. Installation of the Floor Panels:
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Put the floor panels (1) and the seals (3), (4), (5) and (6) in position.
(3)
Apply SPECIAL MATERIALS (Material No. 05-002) to the screws (2).
(4)
Install the screws (2) and TORQUE to 0.42 m.daN (37.16 lbf.in).
(5)
Install the cord (7) FIBER GLASS CORD 1.1MM DIA. (DAN107-1) in the gap between the floor panels (1).
NOTE : Make a loop at the end of the cord, this will help the next
____
removal procedure.
(6) Apply SEALANTS (Material No. 09-005) in the gap between the floor panels (1) and the cutouts of the tiedown positions.
**ON A/C ALL
5. Close-up
________ Subtask 53-22-14-410-050
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the access platform(s).
(3)
Close the FWD cargo-compartment door (Ref. TASK 52-30-00-860-002).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
**ON A/C 301-399,
TASK 53-22-14-000-002 Removal of the Maintenance Panels at Frame 35.5
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific 1 ACCESS PLATFORM 2M (6 FT)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
25-54-12-000-001 Removal of the FWD Cargo Compartment Partition FR34 52-30-00-860-001 Open the FWD or AFT Cargo-Compartment Door with the Yellow Electric Pump 53-22-14-991-003 Fig. 402
3. Job Set-up
__________ Subtask 53-22-14-010-051
A. Get Access
(1)
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身2(31)
