(2)
 Put the floor panels (4) in position. NOTE : Refer to the identification made during the removal procedure.

____

 (3)
 Apply the SPECIAL MATERIALS (Material No. 05-002) to the screws (3).

 (4)
 Install the screws (3) and TORQUE to 0.42 m.daN (37.16 lbf.in).

 (5)
 Install the cord (1) MISCELLANEOUS (Material No. 19-027) in the gap between the floor panels.

 NOTE : Make a loop at the end of the cord, this will help the next
____
 removal procedure.

 (6) Apply the SEALANTS (Material No. 09-016) in the gap between the floor panels.
 EFF : ALL
53-22-12Page 410

 **ON A/C 301-399,
 Subtask 53-22-12-420-050-A
 B. Installation of the Floor Panels
 NOTE : This procedure is applicable for all floor panels.____ (Ref. Fig. 401B/TASK 53-22-12-991-001-B)
 (1) Make sure that the work area is clean and clear of tool(s) and other items.
 (2) If removed, install the heated floor panels ,5DS (6DS), at the FWD emergency exits (Ref. TASK 25-27-51-400-001).
 (3) Put the floor panels (4) in position.
 NOTE : Refer to the identification made during the removal procedure.____ 
R R  (4) Apply the SPECIAL MATERIALS (Material No. 05-002) to the screws (3), (6), (10) and (11).
 (5) Install the screws (3), (10) and (11) and TORQUE to 0.42 m.daN (37.16 lbf.in). 
R  (6) Install the cord (1) MISCELLANEOUS (Material No. 19-027) in the gap between the floor panels.
 NOTE : Make a loop at the end of the cord, this will help the next____ removal procedure. 
R R  (7) Apply the SEALANTS (Material No. 09-016) in the gap between the floor panels.

R **ON A/C ALL
 5. Close-up
________
 Subtask 53-22-12-410-051

 A. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Install the equipment and furnishing, removed to get access to the cabin floor panels.

 (3)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 Subtask 53-22-12-862-050
 B. De-energize the ground service network
 (Ref. TASK 24-42-00-862-001).

 EFF : ALL
53-22-12Page 412

 PANELS - FWD CARGO COMPARTMENT FLOOR - REMOVAL/INSTALLATION
___________________________________________________________
 TASK 53-22-14-000-001
 Removal of the FWD Cargo-Compartment Floor-Panels
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE  QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific nonmetallic scraper
 No specific access platform 1.8 m (5 ft. 11 in.)

 B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
52-30-00-860-001  Open the FWD or AFT Cargo-Compartment Door with the Yellow Electric Pump
R **ON A/C 001-049, 051-099, 101-101, 106-149, 201-299,
 53-22-14-991-001-B Fig. 401 R **ON A/C 102-105,
 53-22-14-991-001 Fig. 401A
 **ON A/C 151-199,

 53-22-14-991-001-A  Fig. 401B
 EFF : ALL
53-22-14Page 401

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
**ON A/C 301-399,
 53-22-14-991-001-C Fig. 401C R **ON A/C 401-499,
R  53-22-14-991-001-D Fig. 401D **ON A/C ALL
 3. Job Set-up
__________
 Subtask 53-22-14-010-050

 A. Get Access
 (1)
 Open the FWD cargo-compartment door (Ref. TASK 52-30-00-860-001).

 (2)
 Put the access platform in position below the FWD cargo-compartment door.

 4. Procedure
_________
 **ON A/C 001-049, 051-099, 101-101, 106-149, 201-299,

 (Ref. Fig. 401/TASK 53-22-14-991-001-B)
 **ON A/C 102-105,

 (Ref. Fig. 401A/TASK 53-22-14-991-001)
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身2(29)