Material No. 11-003 USA ASTM D 740
METHYL-ETHYL-KETONE (Ref. 20-31-00)
Material No. 19-027 F NSA3811
WHITE CORD-BRAIDED (NYLON) (Ref. 20-31-00)
EFF : ALL
53-32-12Page 406
C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External Power
24-42-00-862-001 De-energize the Ground Service Network Supplied from the External Power
25-27-51-400-001 Installation of the Heated Floor Panel 5DS (6DS), 15DS (16DS)
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
53-32-12-991-002 Fig. 401
**ON A/C 301-399,
53-32-12-991-002-A Fig. 401A
**ON A/C ALL
3. Job Set-up
__________
Subtask 53-32-12-860-050
A. Aircraft Maintenance Configuration
(1)
Make sure the ground service network is energized (Ref. TASK 24-42-00-861-001).
(2)
Make sure the necessary equipment and furnishing is removed to get access to the cabin floor panels.
EFF : ALL
53-32-12Page 407
4. Procedure
_________
Subtask 53-32-12-160-050
A. Preparation for Installation R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
(Ref. Fig. 401/TASK 53-32-12-991-002)
**ON A/C 301-399,
(Ref. Fig. 401A/TASK 53-32-12-991-002-A)
**ON A/C ALL
(1) Remove any old sealant from the floor panels with a nonmetallic scraper.
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE
_______
SPECIAL MATERIAL.
THIS MATERIAL IS DANGEROUS.
(2)
Clean the component interface and the adjacent area with CLEANING AGENTS (Material No. 11-003) and lint free cloth.
(3)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(4)
Do an inspection of the component interface and/or the adjacent area.
(5)
Examine the rubber strips (2) for good condition.
EFF : ALL
53-32-12Page 408
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 53-32-12-420-050
B. Installation of the Floor Panels
NOTE : This procedure is applicable for all floor panels.
____
(Ref. Fig. 401/TASK 53-32-12-991-002)
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Put the floor panels (4) in position. NOTE : Refer to the identification made during the removal procedure.
____
(3)
Apply the SPECIAL MATERIALS (Material No. 05-002) to the screws (3).
(4)
Install the screws (3) and TORQUE to 0.42 m.daN (37.16 lbf.in).
(5)
Install the cord (1) MISCELLANEOUS (Material No. 19-027) in the gap between the floor panels.
NOTE : Make a loop at the end of the cord, this will help the next
____
removal procedure.
(6) Apply the SEALANTS (Material No. 09-016) in the gap between the floor panels.
**ON A/C 301-399,
Subtask 53-32-12-420-050-A
B. Installation of the Floor Panels
NOTE : This procedure is applicable for all floor panels.
____
(Ref. Fig. 401A/TASK 53-32-12-991-002-A)
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
If removed, install the heated floor panels, 15DS (16DS), at the AFT emergency exits (Ref. TASK 25-27-51-400-001).
EFF : ALL
53-32-12Page 409
(3) Put the floor panels (4) in position.
NOTE : Refer to the identification made during the removal procedure.____
R R (4) Apply the SPECIAL MATERIALS (Material No. 05-002) to the screws (3), (6), (10) and (11).
(5) Install the screws (3), (10) and (11) and TORQUE to 0.42 m.daN (37.16 lbf.in).
R (6) Install the cord (1) MISCELLANEOUS (Material No. 19-027) in the gap between the floor panels.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身2(102)
