R (4) If the skin offset is not correct, adjust the length of the
R connecting rod (78) as follows:
R (a) Cut and remove the lockwire from the locking devices (75).
R (b) Loosen the jam nuts (76) to release the turnbuckle (77).
R (c) Turn the turnbuckle (77) to set the connection rod (78) to the
R correct length and to adjust the skin offset correctly.
R (d) Tighten the jam nuts (76).
R (e) Safety the jam nuts (76) with lockwire, corrosion-resistant
R steel, 0.8 mm (0.032 in.) on the locking devices (75).
R (5) Adjust the clearance between the vent door stop and the stop of the
R vent door frame as follows:
R (a) Pull the locking handle out of the recess and turn it down to the
R unlocked position to open the vent door.
R (b) Install the adjustment bolts (74) with the jam nuts (73) and new
R tab washers (72) in the hinge arms (71).
R - Make sure that the tab washers (72) are correctly attached on
R the hinge arms (71).
R (c) Close the vent door again (Refer to Para. A.2).
R (d) Turn the adjustment bolts (74) until the clearance is between 0.2
R mm (0.0078 in.) and 0.6 mm (0.0236 in.).
R (e) Tighten the jam nuts (73).
R (f) Safety the jam nuts (73) with the tab washers (72).
R (6) Pull the locking handle out of the recess and turn it down to the
R unlocked position.
5. Close-up
________
Subtask 52-31-11-410-059
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Put the cover assy to the brackets of the cargo door structure and attach it with the related screws and washers (Ref. TASK 52-31-22-400-001).
(3)
Install the lining and insulation (Ref. TASK 52-31-13-400-001).
(4) Install the access panel 825AR.
Subtask 52-31-11-865-057
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1MJ, 3801GX, 3802GX, 3803GX
Subtask 52-31-11-410-060
C. Close Access
(1)
Remove the actuator safety locks and close the FWD and/or AFT cargo door(s) (Ref. TASK 52-30-00-860-002).
(2)
Remove the access platform(s).
1EFF : ALL 1 52-31-11Page 560 1 1 May 01/05 1 1 1CES 1 TASK 52-31-11-820-004
Adjustment of the Door Opening Angle
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific clinometer
No specific access platform 3.5 m (11 ft. 6 in.)
No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft) No specific Torque Wrench : range 2.00 to 20.00 m.daN
(15.00 to 150.00 lbf.ft) 98D52307524000 1 SUPPORT STRUT - CARGO DOORS
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 19-010 USA AMS 5687
LOCKWIRE STAINLESS STEEL ANNEALED 0.8MM DIA
(Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
cotter pins 52-36-02 03 -080
1EFF : ALL 1 52-31-11Page 561 1 1 May 01/05 1 1 1CES 1
D. Referenced Information
-------------------------------------------------------------------------------
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門4(61)
