(1) Install the locking shaft (148) at the cargo door structure as follows:
(a)
Move the locking shaft (148) through the lateral cutout of the cargo door into the sliding bearing of each frame fork end.
(b)
During this movement, assemble the lock cams (145) in the correct sequence on the locking shaft (148).
(c)
Refer to the marks you made during the removal procedure:
-set the lock cams (145) in its correct position on the locking shaft (148)
-assemble the lever (52) and (162) on the locking shaft (148)
-make sure that the attachment holes align.
(d)
Install the tapered pins (165) to attach the lever (162) on the locking shaft (148).
(e)
Install the sleeves (166), the washers (167) and the nuts (168) on the tapered pins (165).
(f)
Install the tapered pins (143) to attach the locking shaft lever
(52) on the locking shaft (148).
(g)
Install the sleeves (142), the washers (141) and the nuts (140) on the tapered pins (143).
(h)
Install the Hi-Lok pins (144) to attach the lock cams (145) on the locking shaft (148).
(i)
Install the washers (147) and the nuts (146) on the Hi-Lok pins (144).
(j)
Tighten the nuts (140), (146) and (168).
R 1EFF : 001-049, 053-099, 101-149, 151-199, 1 52-31-21Page B402 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(2)
Connect the control rod (59) to the locking shaft lever (52) as follows:
(a)
Put the lower fork-end of the control rod (59) on locking shaft lever (52) and install the bolt (57), the washers (55) and the nut (54).
(b)
Tighten the nut (54) and safety it with the new cotter pin (53).
(3)
Connect the connection rod (159) to the lever (162) as follows:
(a)
Put the lower eye-end of the connection rod (159) in the fork-end of the lever (162).
(b)
Install the bolt (160), the washers (161) and the nut (163).
(c)
Tighten the nut (163) and safety it with the new cotter pin (164).
Subtask 52-31-21-820-060-A
C. Adjustment Procedure
(1) Adjust the length of the control rod (56) (part of the linkage mechanism) to make sure that the lock cams (145) are in their correct position (Ref. TASK 52-31-11-820-002).
R **ON A/C 001-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 52-31-21-720-059
D. Do the functional test of the door mechanism to make sure that the locking mechanism operates correctly (Ref. TASK 52-31-00-720-001).
5. Close-up
________
Subtask 52-31-21-865-079
A. Make sure that this(these) circuit breaker(s) is(are) closed:
1MJ, 3801GX, 3802GX, 3803GX.
R 1EFF : 001-049, 053-099, 101-149, 151-199, 1 52-31-21Page B403 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1 Subtask 52-31-21-410-069
B. Close Access
**ON A/C 001-049, 053-099, 101-105, 151-199, 201-220,
(Ref. Fig. 412/TASK 52-31-21-991-021) R **ON A/C 106-149, 221-299, 301-399, 401-499,
(Ref. Fig. 412A/TASK 52-31-21-991-021-A) R **ON A/C 001-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Apply STORAGE PRESERVATION (Material No. 15-005) or STORAGE PRESERVATION (Material No. 15-006) to all the components of the safety shaft assembly and to the adjacent cargo door structure.
(3)
Install the protection plug (6) in the edge member and apply a bead of 09016.
(4)
Install the access panel 825AR on the cargo door.
(5)
Remove the actuator safety locks and close the cargo door (Ref. TASK 52-30-00-860-002).
(6)
Remove the access platform(s).
R 1EFF : 001-049, 053-099, 101-149, 151-199, 1 52-31-21Page B404 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
R **ON A/C 106-149, 221-299, 301-399, 401-499,
TASK 52-31-21-000-014 Removal of the Sequence Shaft Assembly
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM DOORS 艙門4(142)
