A. Get Access
R (1) Put the ACCESS PLATFORM 2M (6 FT) in position below the closed FWD R cargo compartment door (referred to as cargo door).
(2)
Remove the access cover 825AR from the cargo door.
(3)
Open the FWD cargo door and safety it with the actuator safety locks (Ref. TASK 52-30-00-860-001).
1EFF : ALL 1 52-31-32Page 401 1 1 Nov 01/03 1 1 1CES 1 Subtask 52-31-32-865-050
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
122VU DOORS/CARGO 1MJ T12
4. Procedure
_________ Subtask 52-31-32-020-050
A. Removal of the Lock Fitting Components
(Ref. Fig. 401/TASK 52-31-32-991-001)
(1) Make a color mark on the subsequent components to find easier their correct installation position:
-
the serrated plate (4) and the adjusting bush (5),
-
the serrated plate (8) and the eccentric bolt (9). NOTE : This procedure is not necessary when the center punches of
____
these components are aligned.
(2)
Remove and discard the cotter pin (1) from the nut (2).
(3)
Remove the nut (2) and the washer (3) from the eccentric bolt (9).
(4)
Remove the nuts (10) and the washers (11) from the special bolts (12) of the door frame fitting (13).
(5)
Remove the serrated plate (4) from the adjusting bush (5).
(6)
Hold the roll (7) and remove the eccentric bolt (9) together with the serrated plate (8) from the door frame fitting (13).
(7)
Disengage the serrated plate (8) from the eccentric bolt (9).
(8)
Remove the eccentric bush (6) from the roll (7).
(9)
Remove the adjusting bush (5) from the door frame fitting (13).
1EFF : ALL 1 52-31-32Page 402 1 1 Feb 01/98 1 1 1CES 1
Lock Fitting Components
Figure 401/TASK 52-31-32-991-001
1EFF : ALL 1 52-31-32 Page 403
1 1 Feb 01/98
1 1
1CES 1
TASK 52-31-32-400-001
Installation of the Lock Fitting Components
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific access platform 2.0 m (6 ft. 7 in.)
R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft)
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
Material No. 04-011 USA MIL-G-4343
SILICONE GREASE PNEUMATIC SYST AND SEALS
(Ref. 20-31-00)
Material No. 05-027 USA MIL-L-81309
RUST INHIBITOR(FOR CORROSION USE 15-004)
(Ref. 20-31-00)
Material No. 09-016 USA MIL-PRF-81733D TYPE II CLASS B
CORROSION INHIBITING FILLET CONSISTENCY
(Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN
-------------------------------------------------------------------------------
new cotter pin 52-31-32 01 -040
1EFF : ALL 1 52-31-32Page 404 1 1 May 01/05 1 1 1CES 1
D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
52-30-00-860-001 Open the FWD or AFT Cargo-Compartment Door with the Yellow Electric Pump 52-30-00-860-002 Close the FWD or AFT Cargo-Compartment Door with the
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門4(160)
