(2)
 Fully open the door.

 1EFF : ALL 1 52-10-00Page 524 1 1 Aug 01/05 1 1 1CES 1 Subtask 52-10-00-210-063

 D. Visual Inspection of the Girt Bar.
 (1)
 Make sure that the girt bar is still on the door.
 Subtask 52-10-00-410-061

 E. Closing of the Door.

 (1)
 Close the door from the inside.
 **ON A/C 001-049, 051-099, 101-105, 151-199, 201-210,

 Subtask 52-10-00-481-050
 F. Installation of the Safety Pin.
 (1) Install the SAFETY PIN - SLIDE ARMING (98D52103500000) on the emergency control handle and put the handle in the DISARMED position. R **ON A/C 102-149, 201-207, 211-299, 301-399, 401-499,
 Post SB 25-1270 For A/C 102-105,201-207,
 Subtask 52-10-00-481-050-A

 F. Installation of the Safety Pin.
 (1)
 Install the SAFETY PIN - SLIDE ARMING (98D52103500000) on the emergency control handle and put the handle in the DISARMED position.

 (2)
 Close the protection cover to the emergency control handle.

 1EFF : ALL 1 52-10-00Page 525 1 1 Aug 01/05 1 1 1CES 1 **ON A/C ALL

 5. Close-up
________ Subtask 52-10-00-410-086
 A. Close Access
 (1)
 Obey the special safety precautions after the work on the door. (Ref. TASK 52-10-00-860-002)

 (2)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (3)
 Close the passenger/crew door 831, 841, 832, 842 (Ref. TASK 52-10-00-410-001)

 (4)
 Remove the access platform(s).

 1EFF : ALL 1 52-10-00Page 526 1 1 Aug 01/02R 1 1 1CES 1

 TASK 52-10-00-710-002
 Operational Test of the Door Interlock Mechanism

 1.
 Reason for the Job

__________________
 Refer to the MPD TASK: 521000-08

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform 3.5 m (11 ft. 6 in.)
 98D52103500000 1 SAFETY PIN - SLIDE ARMING

 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
52-10-00-010-001 Opening of the Passenger/Crew Door 52-10-00-410-001 Closing of the Passenger/Crew Door 52-10-00-860-001 Special Precautions before Work on the Passenger/Crew
 Door 52-10-00-860-002 Special Precautions after Work on the Passenger/Crew Door
 **ON A/C 001-002,
 52-10-00-991-014 Fig. 503 R **ON A/C 003-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499,
 52-10-00-991-014-A Fig. 503A
 1EFF : ALL 1 52-10-00Page 527 1 1 Aug 01/05 1 1 1CES 1 **ON A/C ALL

 3. Job Set-up
__________
 Subtask 52-10-00-010-061

 A. Get Access WARNING : DO NOT OPEN THE PASSENGER/CREW DOOR IF THE WIND SPEED IS MORE
_______
 THAN 65 KNOTS.

 WARNING : BEFORE YOU START WORK ON THE DOOR, MAKE SURE THAT:
_______
 -
THE EMERGENCY CONTROL HANDLE IS IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.

 -
THE PERCUSSION LEVER OF THE DOOR-DAMPER AND EMERGENCY-OPERATION CYLINDER IS IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.

 WARNING : STOP THE OPENING PROCEDURE IF THE RED WARNING LIGHT FLASHES.
_______ RESIDUAL PRESSURE COULD CAUSE THE DOOR TO OPEN WITH A SUDDEN FORCE AND INJURE PERSONS AND/OR DAMAGE THE AIRCRAFT.
 (1)
 Put the access platform in position at the zone 831 or 841 or 832 or

 842.

 (2)
 Open the applicable passenger/crew door 831, 841, 832, 842 (Ref. TASK 52-10-00-010-001).

 (3)
 Obey the special precautions before you start work on the door. (Ref. TASK 52-10-00-860-001)

 4. Procedure
_________
 Subtask 52-10-00-710-052

 A. Operational Test of the Interlock Mechanism.
 **ON A/C 001-002,

 (Ref. Fig. 503/TASK 52-10-00-991-014) R **ON A/C 003-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499,
 (Ref. Fig. 503A/TASK 52-10-00-991-014-A)
 1EFF : ALL 1 52-10-00Page 528 1 1 Aug 01/05 1 1 1CES 1

 Door Interlock Mechanism
 Figure 503/TASK 52-10-00-991-014 
R 1EFF :  001-002,  1  52-10-00 Page 529 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門1(93)