曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  (c) Open the door. 
R  (2) Check of the screw/nut installation 
R R R R R R  (a) Make sure that the screw (18) is flush with the nut (2). The out-of-flush tolerance J2 is: - for the round section seals: 0 +0 -0.5 mm (0.0000 +0.0000 -0.0196 in.) - for the square section seals: 0 +0 -1 mm (0.0000 +0.0000 -0.0393 in.).
 5. Close-up________
 Subtask 52-11-18-410-055
 A. Close Access
 (1) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
 (2) Obey the special precautions after the work on the door (Ref. TASK 52-10-00-860-002).

 1EFF : ALL 1 52-11-18Page 408 1 1 Nov 01/98 1 1 1CES 1

R R  Door Seal - Clearances Figure 402/TASK 52-11-18-991-006
 1EFF : 1 1 1CES  ALL  1 111 52-11-18 Page 409 Nov 01/98

 

 (3)
 Close the passenger/crew door 831, 841 (Ref. TASK 52-10-00-410-001).

 (4)
 Remove the access platform(s).

 1EFF : ALL 1 52-11-18Page 410 1 1 Nov 01/98 1 1 1CES 1 SEAL - DOOR - REPAIRS

_____________________
 TASK 52-11-18-300-001
 Repair of the Seal of the FWD Passenger/Crew Door
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific clamp
 No specific fine emery paper
 No specific lint-free cloth
 No specific spatula
 No specific very fine emery paper
 No specific Wooden Bonding Block
 No specific access platform 4.40 m (14 ft. 5 in.)

 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 05-023 USA MIL-I-631 POLYTEREPTHALATE (Ref. 20-31-00) Material No. 05-024 FABRIC (Ref. 20-31-00) R Material No. 08-004 USA MIL-A-25457 ADHESIVE SEALANT (Ref. 20-31-00)
 Material No. 11-004  USA MIL-T-81533
 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
 (Ref. 20-31-00)

 1EFF : ALL 1 52-11-18Page 801 1 1 Nov 01/99 1 1 1CES 1

 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
52-10-00-010-001 Opening of the Passenger/Crew Door 52-10-00-410-001 Closing of the Passenger/Crew Door 52-10-00-860-001 Special Precautions before Work on the Passenger/Crew
 Door 52-10-00-860-002 Special Precautions after Work on the Passenger/Crew
 Door 52-11-18-000-001 Removal of the Door Seal 52-11-18-400-001 Installation of the Door Seal 52-11-18-991-002 Fig. 801 52-11-18-991-003 Fig. 802 52-11-18-991-004 Fig. 803 52-11-18-991-005 Fig. 804
 3. Job Set-up
__________
 Subtask 52-11-18-941-051
 A. Get Access
 WARNING : DO NOT OPEN THE PASSENGER/CREW DOOR IF THE WIND SPEED IS MORE
_______
 THAN 65 KNOTS.

 WARNING : BEFORE YOU START WORK ON THE DOOR, MAKE SURE THAT:
_______
 -
THE EMERGENCY CONTROL HANDLE IS IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.

 -
THE PERCUSSION LEVER OF THE DOOR-DAMPER AND EMERGENCY-OPERATION CYLINDER IS IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.

 WARNING : STOP THE OPENING PROCEDURE IF THE RED WARNING LIGHT FLASHES.
_______ RESIDUAL PRESSURE COULD CAUSE THE DOOR TO OPEN WITH A SUDDEN FORCE AND INJURE PERSONS AND/OR DAMAGE THE AIRCRAFT.
 (1)
 Put the access platform in position in the zone 831 or 841.

 (2)
 Open the door 831 or 841 (Ref. TASK 52-10-00-010-001).

 (3)
 Obey the special precautions before you start work on the door (Ref. TASK 52-10-00-860-001).

 1EFF : ALL 1 52-11-18Page 802 1 1 Feb 01/98 1 1 1CES 1 Subtask 52-11-18-020-051

 B. Seal Removal.
 (1) Remove the door seal (Ref. TASK 52-11-18-000-001).
 4. Procedure
_________
 (Ref. Fig. 801/TASK 52-11-18-991-002, 802/TASK 52-11-18-991-003, 803/TASK
 52-11-18-991-004, 804/TASK 52-11-18-991-005) Subtask 52-11-18-340-050
 A. Repair the Signs of Chafing on the Seal.
 WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL

_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門1(163)