Locking Shaft Mechanism-Adjustment Figure 409/TASK 52-11-21-991-016- 22 (SHEET 2)
 1EFF : 1 1R 1CES  ALL  1 11 1 52-11-21 Page 423 May 01/98

 2_ Loosen the nuts (139) and release the lockwashers (140).
 3_ Loosen the clamp (147).
 4_ Turn the barrel of the rod (75) to retract the hook (138) so
 that it does not touch the roller (137).

 (b)
 Remove the cotter pin (68) and discard it.

 (c)
 Remove the nut (69) and the washer (70).

 (d)
 Remove the bolt (74) the washer (73) and the bushes (71) and (72).

 (e)
 Disconnect the rod (75).

 (6)
 Disconnect the rod (80).

 (a)
 Remove the cotter pin (76) and discard it.

 (b)
 Remove the nut (77) and the washer (78).

 (c)
 Remove the bolt (83) the washer (82) and the bushes (81) and (79).

 (d)
 Disconnect the rod (80).

 (7)
 Disconnect the rod (92).

 (a)
 Remove the cotter pin (96) and discard it.

 (b)
 Remove the nut (97) and the washer (95).

 (c)
 Remove the bolt (94), and the bushes (93) and (98).

 (d)
 Disconnect the rod (92).

 (8)
 Disassembly of the Locking Shaft

 (a)
 Remove the cotter pin (101) and discard it.

 (b)
 Remove the nut (102) and the washer (103).

 (c)
 Remove the taper pin (105).

 (d)
 Remove the lever assy (104).

 1EFF : ALL 1 52-11-21Page 424 1 1 Feb 01/02R 1 1 1CES 1

 (e)
 Remove the cotter pin (106), and discard it.

 (f)
 Remove the nut (107) the washer (108).

 (g)
 Push the shaft (117).

 (h)
 Remove the bush (128).

 (i)
 Remove the lever assembly (127) and (129) and the bush (130).

 (j)
 Remove the bush (126).

 (k)
 Remove the bellcranck assembly (125).

 (l)
 Remove the spacer (124).

 (m)
 Remove the lever assembly (122) and the bellcranck assy (123).

 (n)
 Remove the bush (121) and the washer (120) and remove the shaft upper locking (117).

 (o)
 Remove the bush (119) and the washer (118).

 (9) Removal of the bearing assembly (110).
 (a)
 Remove the nuts (109) and the bolts (111).

 (b)
 Remove the bearing assembly (110).

 (10)
 Remove the sealant from the contact surface of the bearing assembly (110).

 (11)
 Clean with CLEANING AGENTS (Material No. 11-004) and MISCELLANEOUS (Material No. 19-003).

 Subtask 52-11-21-020-058
 H. Removal of the Reducer Shaft
 (Ref. Fig. 410/TASK 52-11-21-991-017)

 (1)
 Make sure that the compensation mechanism is released.

 (2)
 Close and lock the door.

 1EFF : ALL 1 52-11-21Page 425 1 1 Feb 01/02R 1 1 1CES 1

 Reducer Shaft Mechanism Figure 410/TASK 52-11-21-991-017
 1EFF : 1 1R 1CES  ALL  1 11 1 52-11-21 Page 426 Feb 01/02

 (3)
 Disconnect the rod (310).

 (a)
 Remove the cotter pin (308) and discard it.

 (b)
 Remove the nut (307) and the washer (309).

 (c)
 Remove the bolt (314) the washer (313) and the bushes (311) and (312).

 (d)
 Disconnect the rod (310).

 (4)
 Disconnect the rod (317).

 (a)
 Remove the cotter pin (320) and discard it.

 (b)
 Remove the nut (322) and the washer (320).

 (c)
 Remove the bolt (315) the washer (316) and the bushes (318) and (319).

 (d)
 Disconnect the rod (317).

 (5)
 Remove the cotter pin (301) and discard it.

 (6)
 Remove the washer (303) and the nut (302).

 (7)
 Remove the washer (327) and the nut (328).

 (8)
 Remove the nut (324) and the bolt (323).

 (9)
 Remove the bearing assy (328).

 (10)
 Push the shaft (330) and remove the spacer (334) the bellcranck (331)

 (332) and (333) the washer (329) and remove the shaft (330).

 (11)
 Remove the nuts (306), the bolt (304) and the bearing assy (305) and the fitting (335).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門1(170)