R 1EFF : 003-049, 051-099, 101-149, 151-199, 1 52-11-00Page 563 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(2)
Make sure that the load necessary to open and close the door with the inner control handle (2) is less than or equal to 16 daN (35.9694 lbf).
(3)
If the load is not in the tolerances, adjust as follows:
(a)
Remove and discard the lockwire from the tension bolt (1),
(b)
Adjust the tension bolt (1) to get the correct load,
(c)
Safety the tension bolt (1) with MISCELLANEOUS (Material No. 19-010),
(4)
Make sure that the inner control handle (2) comes to its initial position with the door on the up position and the low position.
5. Close-up
________ **ON A/C 001-002,
Subtask 52-11-00-410-052
A. Installation of the Component
(1)
Remove the BALLAST WEIGHT - PASSENGER CREW DOOR (98D52103501000) (Ref. TASK 52-10-00-080-001).
(2)
Install the door insulation.
(3)
Install the door lining panels (Ref. TASK 25-23-46-400-001).
(a)
For the left door: 831GZ, 831FZ, 831EZ, 831DZ, 831CZ, 831BZ, 831AZ
(b)
For the right door: 841GZ, 841FZ, 841EZ, 841DZ, 841CZ, 841BZ, 841AZ.
(4)
Install the escape slide (Ref. TASK 25-62-44-400-001).
1EFF : ALL 1 52-11-00Page 564 1 1 May 01/05 1 1 1CES 1R **ON A/C 003-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 52-11-00-410-052-A
A. Installation of the Component
(1)
Remove the BALLAST WEIGHT - PASSENGER CREW DOOR (98D52103501000) (Ref. TASK 52-10-00-080-001).
(2)
Install the door insulation.
(3)
Install the door lining. (Ref. TASK 25-23-46-400-001)
(4) Install the escape slide/raft (Ref. TASK 25-62-44-400-001).
**ON A/C ALL
Subtask 52-11-00-865-057
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 13WN, 15WN, 48WV
Subtask 52-11-00-942-054
C. Close Access
(1)
Obey the special precautions after the work on the door (Ref. TASK 52-10-00-860-002).
(2)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(3)
Close the applicable passenger/crew door 831 or 841 (Ref. TASK 52-10-00-410-001) .
(4)
Remove the access platform(s).
(5)
Make sure that the work area is clean and clear of tool(s) and other items.
1EFF : ALL 1 52-11-00Page 565 1 1 Aug 01/05 1 1 1CES 1 FWD PASSENGER/CREW DOOR - INSPECTION/CHECK
__________________________________________
TASK 52-11-00-200-001
R Detailed Inspection of Door Stop Assemblies on Forward Passenger/Crew Door, R LH/RH
1. Reason for the Job
__________________
Refer to the MPD TASK: 521101-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
R No specific access platform 3.50 m (11 ft. 6 in.)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
52-10-00-010-001 Opening of the Passenger/Crew Door 52-10-00-410-001 Closing of the Passenger/Crew Door 52-10-00-860-001 Special Precautions before Work on the Passenger/Crew
Door 52-10-00-860-002 Special Precautions after Work on the Passenger/Crew Door
52-11-31-000-002 Removal of the Stop Fittings, Buffer, Guide Fittings, Rollers, Door Stop Fittings, Roller Fittings and Guide Arm Fittings
52-11-31-400-002 Installation of the Stop Fittings, the Buffer, the Guide Fittings, the Rollers, the Door Stop Fittings, the Roller Fittings and the Guide Arm Fittings
52-11-00-991-009 Fig. 601
1EFF : ALL 1 52-11-00Page 601 1 1 May 01/03 1 1 1CES 1 1EFF : ALL 1 52-11-00Page 602 1 1 May 01/03 1 1 1CES 1
3. Job Set-up__________
Subtask 52-11-00-010-054
A. Get Access
R (1) Put an access platform in position :
R (a) For the left passenger/crew door, at the zone 831.
R (b) For the right passenger/crew door, at the zone 841.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門1(124)
