(i)
Torque tighten the nuts (18) to between 0.39 and 0.45 m.daN
(34.51 and 39.82 lbf.in).
(j)
Apply SEALANTS (Material No. 09-016) to the areas that follow:
-around the joints between the target (15), the spacer (16) if installed, and the target mounting bracket
-
to the heads and the ends of the screws (14)
-
to the washers (17)
-
to the nuts (18).
R 1EFF : 004-049, 053-099, 101-149, 151-199, 1 32-31-73Page 538 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(4) For the rear proximity sensor 20GA(21GA):
-if the dimension Z is incorrect, do the steps that follow: NOTE : (Dimension Z must be between 1.4 mm (0.0551 in.) and 1.6 mm
____
(0.0629 in.)).
(a)
Disconnect the electrical connector from the applicable proximity sensor 20GA(21GA).
(b)
Put blanking caps on the disconnected electrical connectors.
(c)
Remove the nuts (13), the washers (12) and the screws (10).
(d)
Remove the applicable proximity sensor 20GA(21GA).
(e)
Remove and discard the spacer (11) if installed.
(f)
Make sure that the sensor mounting bracket is in the correct condition.
(g)
If necessary, adjust the new spacer (11) to get the correct dimension Z.
NOTE : It is possible that two spacers are required.
____
(h)
Put the applicable proximity sensor 20GA(21GA) and the new spacer(s) (11) if necessary, in position on the sensor mounting bracket.
(i)
Install the screws (10), the washers (12) and the nuts (13).
(j)
Torque tighten the nuts (13) to between 0.39 and 0.45 m.daN
(34.51 and 39.82 lbf.in).
(k)
Apply SEALANTS (Material No. 09-016) to the areas that follow:
-around the joints between the applicable proximity sensor 20GA(21GA), the spacer (11) if installed, and the sensor mounting bracket
-
to the heads and the ends of the screws (10)
-
to the washers (12)
-
to the nuts (13).
(l)
Remove the blanking caps and connect the electrical connector to the applicable proximity sensor 20GA(21GA).
R 1EFF : 004-049, 053-099, 101-149, 151-199, 1 32-31-73Page 539 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(5) For the forward proximity sensor 22GA(23GA):
-if the dimension X is incorrect, do the steps that follow: NOTE : (Dimension X must be between 3.9 mm (0.1535 in.) and 4.1 mm
____
(0.1614 in.)).
(a)
Measure the dimensions J, K and L.
(b)
Use the formula to calculate the dimension X.
(c)
Remove the nuts (7), the washers (6) and the screws (4).
(d)
Remove the target (3).
(e)
Remove and discard the spacer (5) if installed.
(f)
Make sure that the target mounting bracket is in the correct condition.
(g)
If necessary, adjust the new spacer (5) to get the correct dimension X.
NOTE : It is possible that two spacers are required.
____
(h)
Install the new spacer (5) if necessary, and the target (3) together with the screws (4), the washers (6) and the nuts (7).
(i)
Torque tighten the nuts (7) to between 0.39 and 0.45 m.daN (34.51 and 39.82 lbf.in).
(j)
Apply SEALANTS (Material No. 09-016) to the areas that follow:
-around the joints between the target (3), the spacer (5) if installed, and the target mounting bracket
-
to the heads and the ends of the screws (4)
-
to the washers (6)
-
to the nuts (7).
(6) For the forward proximity sensor 22GA(23GA):
-if the dimension Z is incorrect, do the steps that follow: NOTE : (Dimension Z must be between 1.4 mm (0.0551 in.) and 1.6 mm
____
(0.0629 in.)).
(a)
Disconnect the electrical connector from the applicable proximity sensor 22GA(23GA).
(b)
Put blanking caps on the disconnected electrical connectors.
R 1EFF : 004-049, 053-099, 101-149, 151-199, 1 32-31-73Page 540 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(c)
Remove the nuts (8), the washers (9) and the screws (2).
(d)
Remove the applicable proximity sensor 22GA(23GA).
(e)
Remove and discard the spacer (1) if installed.
(f)
Make sure that the sensor mounting bracket is in the correct condition.
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架5(65)
