R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
32-31-46-991-002-B Fig. 402
**ON A/C 301-399,
32-31-46-991-002-A Fig. 402A
1EFF : ALL 1 32-31-46Page 416 1 1 Aug 01/05 1 1 1CES 1 **ON A/C ALL
3. Job Set-up
__________ Subtask 32-31-46-941-052
A. Safety Precautions
(1)
Make sure that the safety barriers are in position.
(2)
Make sure that the ground safety locks are on the landing gear (Ref. TASK 32-00-00-481-001).
(3)
On the panel 400VU:
-
make sure that the landing-gear control-lever 6GA is in the DOWN position
-
make sure that the warning notice is in position to tell persons not to operate the landing gear.
(4)
Make sure that the warning notices are in position to tell persons not to operate the hydraulic systems:
-in the cockpit, on the HYD overhead panel 40VU - on the hydraulic ground service panels 197CB and 198CB - on the access door 195BB.
Subtask 32-31-46-860-051
B. Aircraft Maintenance Configuration
(1)
Make sure that the aircraft is on jacks (Ref. TASK 07-11-00-581-001).
(2)
Make sure that the Yellow and Green hydraulic systems have been depressurized (Ref. TASK 29-00-00-864-001).
(3)
Make sure that the applicable hydraulic reservoirs have been depressurized (Ref. TASK 29-14-00-614-001).
(4)
Make sure that the isolation coupling of the PTU is disconnected (Ref. TASK 29-23-00-860-001).
R 1EFF : ALL 1 32-31-46Page 417 1 1 May 01/02 1 1 1CES 1 Subtask 32-31-46-869-053
C. Flight Configuration Precautions
(1)
If the electrical power is not necessary for other maintenance tasks, de-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002). Then it is not necessary to operate the LGCIU circuit breakers.
(2)
If the electrical power is necessary, do the precautions for flight configuration with electrical power before you open the circuit breakers (Ref. TASK 32-00-00-860-001).
Subtask 32-31-46-865-051
D. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
49VU L/G/LGCIU/SYS1/NORM 1GA C09 121VU HYDRAULIC/LGCIU/SYS2 2GA Q35 121VU HYDRAULIC/LGCIU/SYS1/GRND SPLY 52GA Q34
4. Procedure
_________
(Ref. Fig. 401/TASK 32-31-46-991-001)
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
(Ref. Fig. 402/TASK 32-31-46-991-002-B)
**ON A/C 301-399,
(Ref. Fig. 402A/TASK 32-31-46-991-002-A)
1EFF : ALL 1 32-31-46Page 418 1 1 Aug 01/05 1 1 1CES 1R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 32-31-46-420-050-B
A. Preparation for Installation
NOTE : In the step that follows, make sure that the Materials No. 04-004
____ and No. 04-022 are not mixed together. Do not use them at the same time (Ref. SIL 12-008).
(1)
Apply a thin layer of COMMON GREASE (Material No. 04-004) or COMMON GREASE (Material No. 04-022) to the interfaces of:
-
the pins (20) and (27)
-
the bearings (26) and (45)
-
the bushes in the fork end (46) of the actuating cylinder.
(2)
Clean the component interface and/or the adjacent area with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架5(22)
