NOTE : When the points of the ambient temperature and the
____ underfloor temperature meet between the given lines of tension, then the correct tension reading will be calculated by linear extrapolation. (See the example on the graph). (Ref. Fig. 503/TASK 32-33-00-991-012)
 (e) Operate the tensiometer. If necessary, adjust the turnbuckle body (9), until the tensiometer shows the same value as you find on the graph.
 1EFF : ALL 1 32-33-00Page 527 1 1 Aug 01/05 1 1 1CES 1

 NLG Cable-Tension Graph Figure 503/TASK 32-33-00-991-012
 1EFF : 1 1R 1CES  ALL  1 11 1 32-33-00 Page 528 Aug 01/05

R  (f) Release the tensiometer. 
R  (g) Operate the tensiometer and make sure that it shows the correct value from the graph. If you do not get the correct value, adjust the turnbuckle body (9), until the value is correct. 
R R  (h) Safety the ends of the cables (2) and (3) and the turnbuckle body (9) with the two locking clips (10). 
R R R R  NOTE : If necessary, increase the cable tension to align the____ locking clips (10) and the turnbuckle body (9). Do not decrease the cable tension to align the locking clips (10) and the turnbuckle body (9).
 (i) Remove the tensiometer.
 (3) To adjust the cables (4) and (5):
 (a) Do the procedure as for the cables (2) and (3).
 (4) Remove the PIN, RIGGING - RUDDER CONTROL at position Pin 3.
 (5) Remove the wedges from the GEAR GRAVITY EXTN operating handle (1).
 Subtask 32-33-00-865-056
 B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1GA, 2GA, 52GA.
 Subtask 32-33-00-710-052
 C. Free Fall Extension System Operation
 CAUTION : MAKE SURE THAT THE RIGGING PINS ARE REMOVED BEFORE OPERATION OF_______ THE FREE FALL SYSTEM. DAMAGE WILL OCCUR IF THE RIGGING PINS ARE INSTALLED DURING SYSTEM OPERATION.

 1EFF : ALL 1 32-33-00Page 529 1 1 Aug 01/05 1 1 1CES 1

 (1) To let the cables and linkages become stable, operate the free-fall extension system through ten full cycles:
 (a) For one full cycle, on the panel 110VU: - operate the GRAVITY GEAR EXTN handle three turns in a clockwise direction at a rate of one turn every five seconds
 - operate the GRAVITY GEAR EXTN handle three turns in a counter-clockwise direction at a rate of one turn every five seconds.
 (2) Lock the GEAR GRAVITY EXTN operating handle (1):
 (a)
 Put the handle (1) in the stowed position.

 (b)
 Put a wedge at each side of the handle (1), to keep it in position and prevent its movement.

 Subtask 32-33-00-860-075
 D. Aircraft Maintenance Configuration
 (1)
 Open the NLG doors (Ref. TASK 32-22-00-010-001).

 (2)
 Make sure that a SAFETY PIN - NLG DOOR is installed in each NLG door (Ref. TASK 32-00-00-481-002).

 (3)
 Put in the PIN, RIGGING - RUDDER CONTROL (98A27901002000) at position Pin 3. Make sure that the bellcrank is locked. (Ref. Fig. 502/TASK 32-33-00-991-011)

 NOTE : If the rigging pin can not be installed, adjust the NLG
____ mechanical system. (Ref. TASK 32-33-00-820-002).
 Subtask 32-33-00-820-074
 E. Adjustment of the NLG Free-Fall Extension Cable System
 (1)
 Adjust the NLG free-fall cables again, as specified in paragraph 4.

 A.

 (2)
 Remove the PIN, RIGGING - RUDDER CONTROL at position Pin 3.

 (3)
 Remove the wedges from the GEAR GRAVITY EXTN operating handle (1).

 1EFF : ALL 1 32-33-00Page 530 1 1 Aug 01/05R 1 1 1CES 1

 Subtask 32-33-00-869-067
 F. Ground Configuration
 (1) If you did the flight configuration precautions, put the aircraft back to the ground configuration (Ref. TASK 32-00-00-860-002).
 Subtask 32-33-00-410-052
 G. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Close the NLG doors (Ref. TASK 32-22-00-410-001).

 (3) Close the lateral avionics-compartment door 822. Subtask 32-33-00-720-052
 H. Test CAUTION : MAKE SURE THAT THE RIGGING PINS ARE REMOVED BEFORE OPERATION OF
_______ THE FREE FALL SYSTEM. DAMAGE WILL OCCUR IF THE RIGGING PINS ARE INSTALLED DURING SYSTEM OPERATION.

 (1) Do a functional test of the landing-gear free-fall extension system (Ref. TASK 32-33-00-720-001).
 5. Close-up
________ Subtask 32-33-00-942-053
 A. Removal of Equipment
 (1)
 Remove the safety barriers.

 (2)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架5(104)