R No specific Torque Wrench : range 0.00 to 1.20 m.daN R (0.00 to 9.00 lbf.ft) R
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 09-016  USA MIL-PRF-81733D TYPE II CLASS B
 CORROSION INHIBITING FILLET CONSISTENCY
 (Ref. 20-31-00)

 Material No. 11-026 GB DEF-STAN 68-148/1
 SOLVENT GENERAL PURPOSE (Ref. 20-31-00)
 Material No. 19-003 USA AMS 3819
 LINT-FREE COTTON CLOTH (Ref. 20-31-00)

 Material No. 19-010  USA AMS 5687
 LOCKWIRE STAINLESS STEEL ANNEALED 0.8MM DIA
 (Ref. 20-31-00)

 1EFF : ALL 1 32-31-73Page 412 1 1 May 01/05 1 1 1CES 1 C. Referenced Information

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-00-00-481-001  Installation of the Safety Devices on the Landing
 Gears
 32-00-00-860-001  Flight Configuration Precautions with Electrical
 Power
 32-00-00-860-002  Ground Configuration after Flight Configuration with
 Electrical Power
 32-12-00-010-001  Open the Main Gear Doors for Access
 32-12-00-410-001  Close the Main Gear Doors after Access
 32-31-73-200-001  Inspection of the MLG Proximity Sensor and Target
 Clearances
 32-69-00-740-001  BITE Check Landing Gear Control Interface Unit
 (LGCIU) using MCDU to Ensure that Continuous BITE is
 Operative
 32-31-73-991-001  Fig. 401
 32-31-73-991-002  Fig. 402
 32-31-73-991-003  Fig. 403
 32-31-73-991-004  Fig. 404
 32-31-73-991-005  Fig. 405
 3. Job Set-up__________
 Subtask 32-31-73-941-056
 A. Safety Precautions

 (1)
 Make sure that the safety barriers are in position.

 (2)
 Make sure that the ground safety locks are on the landing gear (Ref. TASK 32-00-00-481-001).

 (3)
 On the panel 400VU:

 -
make sure that the landing-gear control-lever 6GA is in the DOWN position

 -
make sure that the warning notice is in position to tell persons not to operate the landing gear.

 (4)
 Make sure that the access platform is in position below the zone 734 or 744.

 (5)
 On the panel 110VU, make sure that the warning notice is on the GRAVITY GEAR EXTN handle.

 1EFF : ALL 1 32-31-73Page 413 1 1 May 01/05R 1 1 1CES 1

 Subtask 32-31-73-860-056
 B. Aircraft Maintenance Configuration
 (1)
 Make sure that the access platform is in position below the applicable zone 734 or 744.

 (2)
 Make sure that the applicable MLG door is open (Ref. TASK 32-12-00-010-001).

 (3)
 Make sure that the GROUND LOCK SLEEVE is on the applicable MLG door actuator.

 Subtask 32-31-73-869-060
 C. Flight Configuration Precautions
 (1) If you did not de-energize the aircraft electrical circuits, make sure that the flight configuration precautions are done (Ref. TASK 32-00-00-860-001).
 Subtask 32-31-73-865-055
 D. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
49VU L/G/LGCIU/SYS1/NORM 1GA C09 121VU HYDRAULIC/LGCIU/SYS2 2GA Q35 121VU HYDRAULIC/LGCIU/SYS1/GRND SPLY 52GA Q34
 4. Procedure
_________ Subtask 32-31-73-420-068
 A. Preparation for Installation
 (1)
 Clean the component interface and/or the adjacent area with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026).

 (2)
 Make sure that the parts retained from the removed component are clean and in the correct condition.

R 1EFF : ALL 1 32-31-73Page 414 1 1 May 01/05 1 1 1CES 1

 (3)
 Examine the mountings for the proximity-sensors on the MLG uplock and door uplock to make sure that they are in the correct condition.

 (4)
 Make sure that the applicable bonded shims/spacers are in the correct condition and are not loose.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架5(48)