Material No. 11-026 GB DEF-STAN 68-148/1
 SOLVENT GENERAL PURPOSE (Ref. 20-31-00) Material No. 19-003 USA AMS 3819
 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
 C. Expendable Parts
 -------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
2 cotter pin 32-31-46 01A-040 2 cotter pin 32-31-46 01B-040
 D. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
12-22-32-640-001  Lubrication of the MLG and Doors
 24-41-00-862-002  De-energize the Aircraft Electrical Circuits Supplied from the External Power
 29-00-00-864-001 29-14-00-614-001 29-23-00-860-001 29-23-00-860-002 32-00-00-481-001  Put the Related Hydraulic System in the Depressurized Configuration before Maintenance ActionDepressurization of the Hydraulic ReservoirsDisconnection of the Isolation Coupling of the Power Transfer Unit (PTU)Connection of the Isolation Coupling of the Power Transfer Unit (PTU)Installation of the Safety Devices on the Landing Gears
 32-00-00-860-001  Flight Configuration Precautions with Electrical Power
 32-12-00-010-001 32-12-00-410-001  Open the Main Gear Doors for AccessClose the Main Gear Doors after Access
 SIL 12-008 32-31-46-991-004  (for corrective action)Fig. 404

 1EFF : ALL 1 32-31-46Page 452 1 1 Feb 01/05R 1 1 1CES 1

 3. Job Set-up
__________ Subtask 32-31-46-941-057
 A. Safety Precautions
 (1)
 Make sure that the safety barriers are in position.

 (2)
 Make sure that the MLG doors are open (Ref. TASK 32-12-00-010-001).

 (3)
 Make sure that the ground safety locks are installed on the landing gear (Ref. TASK 32-00-00-481-001).

 (4)
 On the panel 400VU:

 -
make sure that the landing-gear control-lever 6GA is in the DOWN position

 -
make sure that the warning notice is in position to tell persons not to operate the landing gear.

 (5)
 Make sure that the warning notices are in position to tell persons not to operate the hydraulic systems:

 -in the cockpit, on the HYD overhead panel 40VU - on the hydraulic ground service panels 197CB and 198CB - on the access door 195BB.
 Subtask 32-31-46-860-059
 B. Aircraft Maintenance Configuration
 (1)
 Make sure that the Green and Yellow hydraulic systems have been depressurized (Ref. TASK 29-00-00-864-001).

 (2)
 Make sure that the applicable hydraulic reservoirs have been depressurized (Ref. TASK 29-14-00-614-001).

 (3)
 Make sure that the isolation coupling of the PTU is disconnected (Ref. TASK 29-23-00-860-001).

 Subtask 32-31-46-869-059
 C. Flight Configuration Precautions
 (1) If the electrical power is not necessary for other maintenance tasks, de-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002). Then it is not necessary to operate the LGCIU circuit breakers.
 1EFF : ALL 1 32-31-46Page 453 1 1 Feb 01/05R 1 1 1CES 1

 (2) If the electrical power is necessary, do the precautions for flight configuration (Ref. TASK 32-00-00-860-001) before you open the circuit breakers.
 Subtask 32-31-46-865-056
 D. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU L/G/LGCIU/SYS1/NORM 1GA C09 121VU HYDRAULIC/LGCIU/SYS2 2GA Q35 121VU HYDRAULIC/LGCIU/SYS1/GRND SPLY 52GA Q34
 4. Procedure
_________
 (Ref. Fig. 404/TASK 32-31-46-991-004)
 Subtask 32-31-46-420-060
 A. Preparation for Installation
 (1) Make sure that the parts retained from the removed component are clean and in the correct condition.
 NOTE : In the step that follows, make sure that the Materials No.
____ 04-004 or No. 04-022 are not mixed together. Do not use them at the same time (Ref. SIL 12-008).
 (2)
 Apply a thin layer of COMMON GREASE (Material No. 04-004) or COMMON GREASE (Material No. 04-022) to the interfaces of:

 -
the pin (1)

 -
the bearings (9).

 (3)
 Clean the component interface and/or the adjacent area with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架5(31)