(1) Test of the engine red lines exceedances The DMC connected to the upper ECAM DU monitors primary parameter indications of both engines. The maximum values (red lines) of the N1, N2 AND EGT parameters are written in the BITE according to the type of engine installed on the aircraft.
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 31-69-00Page A39 1201-299, 301-302, 1May 01/05 1 1 1CES 1
EIS LRU IDENTIFICATION Display
Figure 058
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 31-69-00Page A40 1201-299, 301-302, 1May 01/05 1 1 1CES 1
DUMP OF THE BITE MEMORY
Figure 059
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 31-69-00Page A41 1201-299, 301-302, 1May 01/05 1 1 1CES 1
INTERNAL & EXTERNAL FAULTS IN FLT Menus
Figure 060 (SHEET 1)
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 31-69-00Page A42 1201-299, 301-302, 1May 01/05 1 1 1CES 1
INTERNAL & EXTERNAL FAULTS IN FLT Menus
Figure 060 (SHEET 2)
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 31-69-00Page A43 1201-299, 301-302, 1May 01/05 1 1 1CES 1
FAULTS ON GND
Figure 061
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 31-69-00Page A44 1201-299, 301-302, 1May 01/05 1 1 1CES 1
MAIN EIS MENU Display
Figure 062
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 31-69-00Page A45 1201-299, 301-302, 1May 01/05 1 1 1CES 1 Should an exceedance occur, the DMC memorizes in its BITE memory the maximum value reached during the last flight leg The ENGINES function (4L) is used to select the ENGINES OVER SPD/TEMP page. On this page several indications give access to the limit values for each engine parameter and the exceedances if these have occurred during the last flight leg. (Ref. Fig. 063) On this page the GENERAL RESET function (4L) serves to reset the exceedance values. This reset is automatically performed at each engine start.
(2) EIS confidence checks The TEST function (4R) on the EIS menu displays the EIS TEST page which present three different tests. (Ref. Fig. 064)
-System Test Operation The SYSTEM TEST performs all the DMC self-tests and checks the computer operation. when the line key adjacent to the SYSTEM TEST indication is pushed, a SYSTEM TEST/PROCEDURE page comes into view and shows indications for test preparation. The RETURN function (6L) is used to select a second page which enables the test to be initiated through the line key adjacent to the START TEST indication (5L). (Ref. Fig. 065) When the test is initiated, the DMC leaves the maintenance mode and records, in the BITE, any occurring failure until the EIS TEST page is selected in order to activate the SYSTEM TEST RESULT function (4L).This action displays the SYSTEM TEST RESULT page to show the results of the test or the TEST OK indication. (Ref. Fig. 065)
-Input test operation (Ref. Fig. 066) During 5 s, the DMC scans all its ONSIDE buses, i.e. it checks that each bus sends labels with their correct refresh rate. During the next 5 s, the DMC scans all its OFFSIDE buses. At the end of this test, the DMC signals all the buses seen as faulty for display on the I/P TEST RESULTS display.
-Display Test (Ref. Fig. 067) When a Display test is selected for a given DMC, the 3 DUs connected to this DMC display a test pattern showing the fundamental colors and geometrical outlines (lines, circles...).
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 31-69-00Page A46 1201-299, 301-302, 1May 01/05 1 1 1CES 1
ENGINES OVERSPD/TEMP Test
Figure 063
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 31-69-00Page A47 1201-299, 301-302, 1May 01/05 1 1 1CES 1
TESTS Menu Figure 064
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1201-299, 301-302, 1 1CES 1 111 31-69-00 Page A48 May 01/05
SYSTEM Test Figure 065
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1201-299, 301-302, 1 1CES 1 111 31-69-00 Page A49 May 01/05
INPUT TEST Operation
Figure 066
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 31-69-00Page A50 1201-299, 301-302, 1May 01/05 1 1 1CES 1
DISPLAY TEST Figure 067
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1201-299, 301-302, 1 1CES 1 111 31-69-00 Page A51 May 01/05
R **ON A/C ALL
D. Configuration of a DMC and its Associated DUs in the Menu Mode
(1)
Display on the DUs connected to a DMC in the maintenance mode As long as a given DMC is in the maintenance mode operation, the DUs connected to this DMC display: MAINTENANCE MODE in green color, instead of the normal operational displays.
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM 指示/記錄系統(tǒng) 8(187)
