Pin prog display Figure 050
R 1EFF : 1 1 1CES 106-149, 303-399, 401-499, 1 111 31-69-00 Page A22 Aug 01/05
RED Lines Figure 051
R 1EFF : 1 1 1CES 106-149, 303-399, 401-499, 1 111 31-69-00 Page A23 Aug 01/05
(Ref. Fig. 052)
Display (C) If the operator has pressed the 2L key he gets display (C) likewise with the red line threshold displayed: N2 RED LINE=106.0%, together with the maximum reached after the last GENERAL RESET N2E1 = NO OVERSPEED The threshold 106.0% has not been reached
Display (D) If the operator has pressed the 3L key the EGT red line threshold is displayed: EGT1 RED LINE=910.0.C, together with the maximum reached after the last GENERAL RESET EGT1 MAX REACHED = 930. 0 .C
Display (E) If the operator has pressed the 3L key whereas the threshold for EGT has not been reached, then he gets the page (E) with the message EGT1 = NO OVERTEMP
(Ref. Fig. 053)
**ON A/C ALL
G. DMC BITE Memory Features and Organization The BITE memory is a 2K-words non volatile EEPROM memory, which is physically implemented with the DMC common memory on the PFD DPU. The BITE memory can be accessed only by the PFD DPU, in order to avoid conflicts with other boards. The DMC BITE is divided into 4 zones: ZONE 1 : recording of EIS internal faults (DMCs, DUs, links) (flight, phases 2 to 9a ) ZONE 2 : recording of all the external faults (input buses) (flight, same conditions) ZONE 3 : recording of the internal fault, but without any flight leg history management (ground, phases 1, 9b, 10) more than 8+30 seconds, 9, 10). ZONE 4 : recording of all the failures, internal and external, in the ground trouble shooting mode. (Ref. Fig. 054)
1EFF : ALL 1 31-69-00Page A24 1 1 May 01/05R 1 1 1CES 1
RED Lines Figure 052
R 1EFF : 1 1 1CES 106-149, 303-399, 401-499, 1 111 31-69-00 Page A25 Aug 01/05
RED Lines Figure 053
R 1EFF : 1 1 1CES 106-149, 303-399, 401-499, 1 111 31-69-00 Page A26 Aug 01/05
R Flight Phases definition Figure 054
1EFF : 1 1 1CES ALL 1 111 31-69-00 Page A27 Feb 01/05
3. Operation in the Normal Mode
____________________________
A. Transmission of Failure Information In the normal operational mode, i.e. with EFIS and ECAM images normally displayed on the DUs, the failures are automatically transmitted to the CFDIU as soon as they are detected, isolated and stored in the BITE memory, but only in the so-called flight phases, i.e. from 2 to 9a. On the ground, in phases 1, 9b and 10, only the EIS internal faults are recorded, but they are not transmitted. They can be read only in the menu mode, by a dump of the zone 3. However, the DMC still continues sending the failure messages of the last flight leg, i.e. those recorded in the flight phases of the last flight leg. The DMCs constantly know which failures they must record and in which BITE memory zone they must store them by decoding the command code transmitted by the CFDIU on its label 227. (Ref. Fig. 054)
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-299, 301-302,
B. Messages Transmitted for the Different Possible Failures For the DMCs: GMT : 1105 ATA : 31-63-34 line given by the CFDIU DMCX (with X = 1, 2 or 3) For the DUs: GMT : 1105 ATA : 31-63-22 DUXXXXX (with XXXXX = PFD1, ND1, ECAM 1, ECAM 2, ND2, PFD2) For the DMC-DU links GMT : 1105 ATA : 31-63-22 DMCX-DUXXXXX LINK For the input buses GMT : 1105 ATA : YYYYYY (with YYYYYY = ATA REF of the source from which the bus is seen faulty, see table of ATA REF codes). DMCX : NO XXXXXX DATA with XXXXXX = IRSX, ADCX, ECUXX, EECXX, FACX, FQIX, ECP, SDACX, FWCX, TCAS, ILSX, R/AX, DMEX, VORX, ADFX, FGCX (for FMGCX-A), FMCX (for FMGCX-EFIS),
R **ON A/C 001-049, 051-061, 101-103, 201-203,
WXRX,
(with X = CHANNEL 1 or 2)
1EFF : ALL 1 31-69-00Page A28 1 1 May 01/05 1 1 1CES 1
R **ON A/C 001-049, 101-105, 151-199, 201-299, 301-302,
R Post SB 31-1127 For A/C 001-049,101-103,201-203,
WXR1 CH Y (with Y = CHANNEL 1 or 2)
R **ON A/C 056-056, 058-058, 061-099,
R Post SB 31-1127 For A/C 056-056,058-058,061-061,
R R WXR1/2 CH Y (with Y = CHANNEL 1 or 2)
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-299, 301-302,
FCU-X, LGCIUX, FCDCX, CFDIU). - For the RS-422 message bus from the FWCs: DMCX : NO FWCX MSG For the wiring problems: GMT : 1105 ATA : 31-63-34 DMCX : PROGRAM PIN | | GMT : 1105 ATA : 31-63-34 | Checked during the DMCX : POSITION PIN | Power On Self Test Only | GMT : 1105 ATA : 31-63-22 | DMCX : DUXXXXX POSITION PIN |
GMT : 1105 ATA : 31-63-34 DMCX : RECONF WIRING | If a DU Alternate Control| is not carried out
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 指示/記錄系統 8(184)
