(2)
Make sure that the parts retained from the removed component are clean and in the correct condition.
1EFF : ALL 1 27-34-51Page 459 1 1 May 01/05R 1 1 1CES 1
4. Procedure
_________
(Ref. Fig. 406/TASK 27-34-51-991-005) Subtask 27-34-51-420-057
A. Install the servo control actuator MSVT
(1)
Apply COMMON GREASE (Material No. 04-004) to the bolts (4).
(2)
Install the O rings (6) and (7) in the MSVT (3).
(3)
Put the MSVT (3) in position on the servo control actuator and support it.
(4)
Install the washers (5) and the bolts (4) into the MSVT (3).
(5)
TORQUE the bolts (4) to between 0.33 and 0.41 m.daN (29.20 and 36.28 lbf.in)
(6)
Remove the blanking caps.
(7)
Connect the electrical connectors. Subtask 27-34-51-081-053
B. Remove Locking Devices
(1) Remove the PIN-SIDE STICK LOCKING from the CAPT and F/O side stick controllers.
(2)
Remove the SETTING TOOL-NEUTRAL, ELEVATOR from the elevator. Subtask 27-34-51-865-059
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 15CE1, 15CE2, 16CE1, 16CE2, 19CE1, 19CE2, 19CE3, 20CE1, 20CE2, 21CE1, 21CE2, 22CE
Subtask 27-34-51-710-053
D. Operational Test
(1) Do an operational test of the servo controls. (Ref. TASK 27-34-00-710-001)
1EFF : ALL 1 27-34-51Page 460 1 1 May 01/05R 1 1 1CES 1
5. Close-up
________ Subtask 27-34-51-410-055
A. Visual Inspection
(1) Make sure that the work area is clean and clear of tool(s) and other items.
Subtask 27-34-51-410-056
B. Close Access
(1) Close the trailing edge access panels 334DB and/or 344DB (Ref. TASK 55-13-11-400-001)
Subtask 27-34-51-942-055
C. Remove Ground Equipment
(1)
Remove the warning notice(s).
(2)
Remove the access platform(s).
1EFF : ALL 1 27-34-51Page 461 1 1 May 01/05R 1 1 1CES 1
TASK 27-34-51-000-009 Removal of the Servo Control Actuator Eye-End WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE CLEAR.
_______ MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES ARE
_______ CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : WEAR AND ATTACH A SAFETY HARNESS WHEN YOU WORK ON HIGH SECTIONS. A
_______ FALL CAN INJURE OR KILL YOU.
CAUTION : DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE MADE OF
_______ CARBONFIBER REINFORCED PLASTIC.
1. Reason for the Job__________________ Self explanatory.
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific variable access platform No specific warning notices 98D27309001000 1 TOOL-ELEVATOR NEUTRAL SETTING 98D27903500000 2 PIN-SIDE STICK LOCKING
1EFF : ALL 1 27-34-51Page 462 1 1 May 01/05R 1 1 1CES 1
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱3(73)
