曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 WARNING : OBEY THE HYDRAULIC SAFETY PROCEDURES._______
 (1) Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002).
 (2) If applicable, disconnect the Power Transfer Unit (PTU) (Ref. TASK 29-23-00-860-001).
 NOTE : The flaps move at full-speed if the Power Transfer Unit (PTU)____ is in operation. If the PTU is disconnected (electrically or hydraulically), only the yellow flap motor operates and the flaps move at half-speed.
 NOTE : An ECAM F/CTL FLAP SYS 1 FAULT message will show when the PTU____ is isolated. This message can be ignored.
 (3) Pressurize the Yellow hydraulic system (Ref. TASK 29-10-00-863-002).
 (4) Pressurize the Blue hydraulic system (Ref. TASK 29-10-00-863-003).
 NOTE : The Blue and/or Green hydraulic system(s) operate(s) the slat____ system. If necessary, use the alternative hydraulic system. 
R  Subtask 27-50-00-865-072 
R R  C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged 
R R R R R  -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU AUTO FLT/FAC1/26VAC 14CC1 B03 121VU AUTO FLT/FAC2/26VAC 14CC2 M18

 

 Subtask 27-50-00-865-070
R D. Make sure that this(these) circuit breaker(s) is(are) closed:
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 121VU FLIGHT CONTROLS/WTB/FLP/SYS2 12CV P20 121VU FLIGHT CONTROLS/WTB/SLT/SYS2 11CV P19 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21 122VU FLIGHT CONTROLS/WTB/FLP/SYS1 10CV S07 122VU FLIGHT CONTROLS/WTB/SLT/SYS1 9CV S06
 4. Procedure
_________
 Subtask 27-50-00-866-062
 A. Retraction of the Flaps/Slats on the Ground
 WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
 (1)
 Do the EIS start procedure (Ref. TASK 31-60-00-860-001).

 (2)
 Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (Ref. TASK 27-00-00-080-002).

 (3)
 Set the flap/slat control lever to the applicable position 3, 2, 1 or

 0.

 (4)
 Make sure that on the ECAM upper DU:

 -
the flap position bar moves to the set position

 -
the slat position bar moves to the set position.

 

 

 5. Close-up________
 Subtask 27-50-00-860-068
 A. Aircraft Maintenance Configuration
 (1) Depressurize the Yellow hydraulic system (Ref. TASK 29-10-00-864-002).
 (2) Depressurize the Blue hydraulic system (Ref. TASK 29-10-00-864-003).
 (3) If applicable, connect the PTU (Ref. TASK 29-23-00-860-002).
 (4) Do the EIS stop procedure (Ref. TASK 31-60-00-860-002).
 (5) De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002). 
R  Subtask 27-50-00-865-073 
R R R  B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 14CC1, 14CC2
 Subtask 27-50-00-942-064 
R  C. Removal of Equipment
 (1) Make sure that the work area is clean and clear of tool(s) and other items.
 (2) Remove the safety barriers.
 (3) Remove the warning notice(s).
 (4) Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 

 TASK 27-50-00-866-012
 Manual Retraction of the Flaps
 WARNING : MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING
_______
 NOTICES ARE IN POSITION.

 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific pneumatic right-angle wrench
 No specific safety barriers
 No specific warning notice
 No specific access platform 2.5 m (8 ft. 2 in.)
 460005835 2 GROUND LOCK SLEEVE
 98D27504005000 1 PIN RIGGING-FLAPS (TRACK 1)
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱3(195)