(3)
Remove the BAR-TURNING from the flap drive shaft.
5. Close-up
________ Subtask 27-50-00-865-067
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV, 10CV, 12CV
Subtask 27-50-00-410-051
B. Close Access
(1)
Install the torque shaft assy 6204CM (6254CM) (Ref. TASK 27-54-45-400-002).
(2)
Remove the PIN RIGGING-FLAPS (TRACK 1) from the track 1 rigging pin position.
(3)
Make sure that the work area is clean and clear of tool(s) and other items.
(4)
Remove the access platform(s).
(5)
Close the MLG doors (Ref. TASK 32-12-00-410-001).
1EFF : ALL 1 27-50-00Page 229 1 1 May 01/04R 1 1 1CES 1
Subtask 27-50-00-860-063
C. Aircraft Configuration
(1) On the MCDU:
(a) Get access to the SYSTEM REPORT/TEST F/CTL page (Ref. TASK 31-32-00-860-006).
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the MCDU: On the MCDU:
-push the line key for <SFCC1(2) - the MCDU shows the SFCC1(2) menu page
1.
2. Push the NEXT PAGE button - the MCDU shows the SFCC1(2) menu page
2.
3.
Push the line key (2L) SYSTEM - the MCDU shows the flap SYSTEM DATA DATA FLP> submenu.
4.
Push the line key (1L) <PPU - the MCDU shows the PPU DATA page(s).
5.
Record the APPU data.
(2)
Make sure that the PPU DATA shown is within 0.1 deg. of the value as recorded before the manual extension.
(3)
If the PPU DATA is not within 0.1 deg., do an adjustment of the flap rigged position (Ref. TASK 27-51-00-820-005).
(4)
Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER from the flap/slat control lever on the panel 114VU.
(5)
De-energize the ground service network
(Ref. TASK 24-42-00-862-001).
Subtask 27-50-00-942-061
D. Close-up
(1)
Remove the warning notice(s).
(2)
Remove the safety barriers.
(3)
Make sure that the work area is clean and clear of tool(s) and other items.
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 27-50-00Page 230 1 1 May 01/04R 1 1 1CES 1
TASK 27-50-00-866-010
Reset of the Torque Limiters of the Flap System on the Ground
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notices
No specific access platform 4 m (13 ft. 1 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied
from the External Power
27-54-00-710-001 Operational Test of the Flap System
29-10-00-863-002 Pressurize the Yellow Hydraulic System
29-10-00-864-002 Depressurize the Yellow Hydraulic System
R 57-51-37-000-002 Removal of the Access Panels 573AB(673AB), R 573BB(673BB), 573CB(673CB) -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
57-51-37-000-004 Removal of the Access Panels 575AB/575BB/575CB/575DB/575EB/575FB/575GB/575HB (675AB/675BB/675CB/675DB/675EB/675FB/675GB/675HB)
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱3(197)
