R (Ref. Fig. 505/TASK 27-34-00-991-010)
(5) Adjust the outboard servocontrol to the new neutral position: (Ref. Fig. 501/TASK 27-34-00-991-001)
(a)
Remove and discard the lockwire from the lock nut (2).
(b)
Loosen the lock nut (2).
(c)
Disengage the lock washer (3).
(d)
Turn the rod (4) (in the correct direction) until: 1 The pointer on the trailing edge of the elevator is in line
_ with the mark made before on the adhesive tape.
2 You can easily engage/disengage the rigging pin into/from the
_ elevator position transducer-unit (1).
(e)
Engage the lock washer (3).
(f)
TORQUE the lock nut (2) to between 3 and 3.5 m.daN (22.12 and
25.81 lbf.ft)
(g)
Make sure that the adjustment does not change when you TORQUE the lock nut.
(h)
Safety the lock nut (2) with Lockwire-corrosion resistant steel dia 0.8 mm (0.03 in.).
(i)
Remove the adhesive paper tape.
(j)
Install a new reference triangle (8) on the tail cone with its center in line with the pointer on the trailing edge of the elevator (Ref. TASK 11-00-00-960-001).
(k)
Depressurize the Blue hydraulic system (Ref. TASK 29-10-00-864-003).
Subtask 27-34-00-480-060
D. Installation of the Tools
R (1) Install the GAUGE-ELEVATOR NEUTRAL SETTING (98D27309002000) on the left side: (Ref. Fig. 506/TASK 27-34-00-991-008)
(a)
Remove the pin (2) and the wedge (3) from the side plates (6).
(b)
Turn the adjuster knob (11) counterclockwise until the setting bar (10) is in its highest position.
(c)
Install the tool (1) on the hinge bearing of the elevator and THS:
-
the rib (7) must be between the side plates (6).
-
the abutment block (8) must touch the rib (7).
-
the stop (4) must touch the elevator hinge bearing (5).
(d)
Install the pin (2) through the side plates (6) and the stop (4).
(e)
Install the wedge (3) through the side plates (6).
(f)
Put the gauge (12) (5th mark) between the setting bar (10) and the abutment block (8).
(g)
Turn the adjuster knob (11) to lower the setting bar (10) until:
1 The pad (9) touches the THS.
_
2 The bottom of the setting bar (10) is to be 5 mm (0.1968 in.)
_
from the abutment block (8).
(2)
Install the LOAD APPLICATION TOOL - ELEVATOR, AILERON, RUDDER (98D27303000001) at the trailing edge of the elevator between the two servocontrols.
(3)
Remove the pointer of the LOAD APPLICATION TOOL - ELEVATOR, AILERON, RUDDER (98D27303000001) from the right side and install it on the left side, on the trailing edge of the elevator, in front of the tail cone. (Ref. Fig. 505/TASK 27-34-00-991-010)
(4)
Install an adhesive paper tape on the tail cone in front of the pointer.
Subtask 27-34-00-820-068-A
E. Adjustment of the Inboard Servocontrol of the Left Elevator
R (1) On the maintenance panel 50VU, push the HYD/LEAK MEASUREMENT VALVES/G R pushbutton switch. (the OFF legend of the HYD/LEAK MEASUREMENT R VALVES/G comes on).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱3(37)
