曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

locations for correct installation of the tail cone.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-31-71
Page 401
Oct 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(b) Do this task: Tailcone Removal, TASK 53-53-00-000-801.
SUBTASK 27-31-71-860-002
(3) Use the bar, SPL-1677 to set the horizontal stabilizer to 4 units of trim.
SUBTASK 27-31-71-080-001
(4) Install the rig pin E-5 from the rig pin kit, SPL-1585 on the elevator aft quadrant.
SUBTASK 27-31-71-010-001
(5) To get access to the turnbuckles, do this task:
Open this access panel:
Number Name/Location
311BL Stabilizer Trim Access Door
F. Torque Tube Removal
SUBTASK 27-31-71-020-002
(1) Remove the cables EAL, EBL, EAR, and EBR from the quadrants [5] (Figure 401, Figure 402):
(a) Install the clamps on the cables so the cables will not go through the aft pressure bulkhead.
(b) Remove the turnbuckles locking clips.
(c) Loosen the turnbuckles for the elevator cables EAL, EBL, EAR, and EBR (Figure 401).
(d) Remove the nuts [4], washers [3], bolts [1], and cable retainers [2] from the four quadrants
[5].
(e) Remove the cables from the quadrants [5].
SUBTASK 27-31-71-020-003
(2) Remove the torque tube [18]:
(a) Remove the nuts [16], washers [15], and bolts [14] to disconnect the elevator position
sensor rod [13] from the torque tube [18] (Figure 402) (View B).
(b) Remove the nut [29], washer [28], washer [27], and bolt [26] to disconnect the autopilot
actuator rod [19] from the input crank [30] (Figure 402)(View C).
(c) Remove the nuts [11], washers [10], washers [9], and bolts [8] to disconnect the four input
rods [7] of the elevator power control units [6] from the four input cranks [12] (Figure 402)
(Views B and E).
(d) Remove the nut [24], washer [23], washer [22], and bolt [21] to disconnect the feel and
centering rod [20] from the input crank [25] (Figure 402)(View C).
(e) Use the drill bit 0.247/0.250 and the drill centering guide to drill out the lockbolts [32] and
collars [33] from the center bearing retainer [31] (Figure 402) (View D).
1) Make sure the holes are not out of tolerance.
(f) Remove the rig pin E-5 from the elevator aft quadrant.
(g) Remove the nuts [43], washers [42], nuts [41], washers [40], bolt assemblies [38], and
bushings [39] to disconnect the two elevator power control units [6] from the torque tube
[18] (Figure 402) (View A-A).
GUN 013-099, 101-122; GUN 001-012, 155-157, 201-999 POST SB 737-27A1271
(h) Remove the bolt shrouds [54] from the left and right assemblies.
NOTE: There is a bolt shroud [54] on the bolt heads and the nut ends of the bolts [44].
GUN ALL
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-31-71
Page 402
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(i) Remove the nuts [47], washers [46], bolts [44], and bushings [45] to disconnect the two
reaction links [37] from the torque tube [18].
(j) Remove the nuts [48], washers [49], nuts [50], washer [52], washers [51], washers [34], bolt
assemblies [35], and bushings [53] to disconnect the torque tube [18] from the support
structure.
(k) Remove the torque tube [18] from the airplane.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-31-71
Page 403
Oct 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Elevator Cable and Turnbuckle Locations
Figure 401 (Sheet 1 of 2)/27-31-71-990-801
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-31-71
Page 404
Jun 10/2004
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Elevator Cable and Turnbuckle Locations
Figure 401 (Sheet 2 of 2)/27-31-71-990-801
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-31-71
Page 405
Jun 10/2004
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Elevator Input Torque Tube Installation
Figure 402 (Sheet 1 of 8)/27-31-71-990-802
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-31-71
Page 406
Jun 10/2004
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Elevator Input Torque Tube Installation
Figure 402 (Sheet 2 of 8)/27-31-71-990-802
737-600/700/800/900
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 AIRCRAFT MAINTENANCE MANUAL飛機維護手冊3(85)