曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Stabilizer-to-Body Seal Adjustment
Figure 406/27-41-11-990-804
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-41-11
Page 425
Feb 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
HORIZONTAL STABILIZER LEADING EDGE - REMOVAL/INSTALLATION
1. General
A. This procedure has these tasks:
(1) A removal of a horizontal stabilizer leading edge
(2) An installation of a horizontal stabilizer leading edge.
B. The horizontal stabilizer leading edge is referred to as the "leading edge" in this procedure.
C. This procedure is applicable for the left and right leading edges.
TASK 27-41-21-000-801
2. Horizontal Stabilizer Leading Edge Removal
(Figure 401)
A. Location Zones
Zone Area
331 Left Horizontal Stabilizer - Removable Leading Edge
341 Right Horizontal Stabilizer - Removable Leading Edge
B. Procedure
SUBTASK 27-41-21-020-001
(1) Remove the leading edge [3]:
(a) Using non-metallic tools, remove seal from leading edge [3] and tip cap assembly [4].
(b) Remove the bolts from the tip cap assembly [4] and slightly move out enough so the
leading edge [3] can be remove.
(c) Remove the bolts [1] that attach the lower surface and the inboard of the leading edge [3] to
the front spar.
(d) Hold the leading edge [3] and remove the bolts [1] that attach the top surface of the leading
edge [3] to the front spar.
(e) Hold each end of the leading edge [3].
(f) Remove the leading edge [3] from the airplane.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-41-21
Page 401
Feb 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Horizontal Stabilizer Leading Edge Installation
Figure 401/27-41-21-990-801
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-41-21
Page 402
Feb 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
TASK 27-41-21-400-801
3. Horizontal Stabilizer Leading Edge Installation
(Figure 401)
A. Consumable Materials
Reference Description Specification
A00247 Sealant - Pressure And Environmental - Chromate
Type
BMS5-95
A00900 Sealant - Silicone, RTV - Dow Corning 93-006-1
B. Location Zones
Zone Area
331 Left Horizontal Stabilizer - Removable Leading Edge
341 Right Horizontal Stabilizer - Removable Leading Edge
C. Procedure
SUBTASK 27-41-21-420-001
(1) Install the leading edge [3]:
(a) Lift and put the leading edge [3] in its position.
(b) Make sure the clearance between the leading edge [3] and the horizontal stabilizer [2] is
0.040 in. (1.02 mm) -- 0.130 in. (3.30 mm).
(c) Install the bolts [1] that attach the top surface of the leading edge [3] to the front spar.
(d) Install the bolts [1] that attach the lower surface and inboard of the leading edge [3] to the
front spar.
(e) Install tip cap assembly [4].
(f) Fill the clearance between the leading edge [3] and the horizontal stabilizer [2] with Dow
Corning 93-006-1 sealant, A00900 or sealant, A00247.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-41-21
Page 403
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
HORIZONTAL STABILIZER CENTER SECTION HINGE FITTING - REMOVAL/INSTALLATION
1. General
A. This procedure has these tasks:
(1) A removal of a horizontal stabilizer center section hinge fitting
(2) An installation of a horizontal stabilizer center section hinge fitting.
B. The horizontal stabilizer center section hinge fitting is referred to as the "hinge fitting".
C. You can remove the hinge fitting of the horizontal stabilizer center section hinge (which has the hinge
bearing) without the removal of the outboard stabilizer sections.
D. This procedure is applicable for the left and right hinge fittings.
E. You must do the removal and installation of the hinge fitting on one side at a time.
TASK 27-41-31-000-801
2. Horizontal Stabilizer Center Section Hinge Fitting Removal
(Figure 401, Figure 402)
A. Tools/Equipment
NOTE: When more than one tool part number is listed under the same "Reference" number, the
tools shown are alternates to each other within the same airplane series. Tool part numbers
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 AIRCRAFT MAINTENANCE MANUAL飛機維護手冊3(131)