曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

that are replaced or non-procurable are preceded by "Opt:", which stands for Optional.
Reference Description
SPL-1672 Assembly - Lock, Stabilizer Trim
(Part #: F71336-501, Supplier: 81205, A/P Effectivity: 737-100, -200,
-200C, -300, -400, -500, -600, -700, -700C, -700ER, -700QC, -800, -900,
-900ER, -BBJ)
SPL-2026 Set - Punch, Horizontal Stabilizer Center Section
(Part #: C55002-1, Supplier: 81205, A/P Effectivity: 737-300, -400, -500,
-600, -700, -700C, -700ER, -700QC, -800, -900, -900ER, -BBJ)
B. Location Zones
Zone Area
211 Flight Compartment - Left
212 Flight Compartment - Right
333 Left Horizontal Stabilizer - Rear Spar to Trailing Edge
343 Right Horizontal Stabilizer - Rear Spar to Trailing Edge
C. Access Panels
Number Name/Location
331A Horizontal Stabilizer, Gap Cover
331AZ Horizontal Stabilizer, Access Panel, Inboard L.E. Closure Rib
332AB Horizontal Stabilizer, Gap Cover, Horizontal Stabilizer to Body
341A Horizontal Stabilizer, Gap Cover
341AZ Horizontal Stabilizer, Access Panel - Inbd L.E. Closure Rib
342AB Horizontal Stabilizer, Gap Cover - H. Stab. to Body
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-41-31
Page 401
Jun 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
D. Prepare for the Removal
WARNING: MAKE SURE THAT ALL PERSONNEL, AND EQUIPMENT ARE AWAY FROM THE
HORIZONTAL STABILIZER. THE MOVEMENT OF THE HORIZONTAL STABILIZER
DURING MAINTENANCE CAN CAUSE INJURY TO PERSONNEL, AND DAMAGE TO
EQUIPMENT.
SUBTASK 27-41-31-860-001
(1) Set the stabilizer to the maximum leading edge down position using the stabilizer trim wheel.
SUBTASK 27-41-31-860-002
(2) Set the stabilizer trim cutout switches to the CUTOUT position.
NOTE: The stabilizer trim cutout switches are installed on the control stand.
SUBTASK 27-41-31-860-003
(3) Open these circuit breakers and install safety tags:
CAPT Electrical System Panel, P18-1
Row Col Number Name
C 2 C00849 AFCS STABILIZER TRIM
F/O Electrical System Panel, P6-2
Row Col Number Name
B 10 C00207 FLIGHT CONTROL STAB TRIM CONT
D 10 C00840 FLIGHT CONTROL STAB TRIM ACTUATOR
SUBTASK 27-41-31-480-001
(4) Install the lock, SPL-1672 on the stabilizer trim wheel at the control stand (Figure 401):
(a) Turn the trim wheel to put the handle at the top of the wheel.
(b) Adjust the height of the trim lock to put the trim wheel handle correctly on the yoke.
(c) Install the pin through the yoke.
(d) Install the safety pin.
SUBTASK 27-41-31-010-001
(5) To gain access to the left hinge fitting, do this step:
Open these access panels:
Number Name/Location
331A Horizontal Stabilizer, Gap Cover
331AZ Horizontal Stabilizer, Access Panel, Inboard L.E.
Closure Rib
332AB Horizontal Stabilizer, Gap Cover, Horizontal
Stabilizer to Body
SUBTASK 27-41-31-010-002
(6) To gain access to the right hinge fitting, do this step:
Open these access panels:
Number Name/Location
341A Horizontal Stabilizer, Gap Cover
341AZ Horizontal Stabilizer, Access Panel - Inbd L.E.
Closure Rib
342AB Horizontal Stabilizer, Gap Cover - H. Stab. to Body
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-41-31
Page 402
Jun 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
E. Hinge Fitting Removal
(Figure 402)
SUBTASK 27-41-31-020-001
NOTE: You must do the removal and installation of the hinge fitting on one side at a time.
(1) Remove the hinge fitting [24] from the bulkhead support structure:
(a) Remove the pin [20], nut [19], and washer [21]. Discard the pin [20].
(b) Remove the pin [22], nut [18], bushing spacer [23]. Discard the pin [22].
(c) Remove the bolts [2] and washers [3] from the bushing retainer [1].
(d) Remove the bushing retainer [1].
(e) Use the set, SPL-2026 and push out these parts:
1) The hinge insert pin [27]
2) The bushing retainer [25]
3) The hinge pin [26].
(f) Remove the adjustable hinge bushing [28], bushing spacer [16], and hinge bushing [17].
NOTE: The bushing spacer [16] will come off when you remove the adjustable hinge
bushing [28].
SUBTASK 27-41-31-020-002
(2) Remove the upper thrust brace [38] and lower thrust brace [39]:
(a) Remove the pin [37], nut [36], washer [35], washer [34], and bolt [33] that attach the upper
thrust brace [38] and lower thrust brace [39] to the thrust brace fitting [51].
NOTE: Use a marker or a pin to make marks on the upper thrust brace [38] and lower
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 AIRCRAFT MAINTENANCE MANUAL飛機維護手冊3(132)