曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

OCCUR.
(1) Do the stabilizer trim cutout test:
(a) Make sure that the main cutout switch, S272 on the control stand is in the NORMAL
position.
(b) Set the STAB TRIM switch on the stab trim and cabin door, P8-47 module, to the NORM
position.
(c) Position the stabilizer to an intermediate position (Approximately 8 units of trim is
satisfactory).
(d) Move and hold the STAB TRIM switches on the captain’s control wheel to the NOSE UP
position.
1) Make sure that the stabilizer leading edge moves down (APL NOSE UP).
2) While the stabilizer moves, push the captain’s control column forward until the column
cutout switch stops the stabilizer.
3) Immediately release the control column to the neutral position with the two stab trim
switches still held in the nose up position.
4) With the control column in the neutral position, make sure the stabilizer leading edge
continues to move down.
5) Release the STAB TRIM switches.
(e) Move and hold the STAB TRIM switches on the captain’s control wheel to the NOSE DOWN
position.
1) Make sure that the stabilizer leading edge moves up (APL NOSE DOWN).
2) While the stabilizer moves, pull the captain’s control column aft until the column cutout
switch stops the stabilizer.
3) Immediately release the control column to the neutral position with the two stab trim
switches still held in the nose down position.
4) With the control column in the neutral position, make sure the stabilizer leading edge
continues to move up.
5) Release the STAB TRIM switches.
(f) Position the stabilizer to an intermediate position (Approximately 8 units of trim is
satisfactory).
(g) Move and hold the STAB TRIM switches on the captain’s control wheel to the NOSE UP
position.
1) Make sure that the stabilizer leading edge moves down (APL NOSE UP).
2) While the stabilizer moves, push the captain’s control column forward until the column
cutout switch stops the stabilizer.
3) Hold the captain’s control column in this position and immediately release the STAB
TRIM switches.
4) Use a control column assembly protractor, SPL-1680 to make sure the captain’s control
column is between 2.90 and 3.70 degrees forward from the neutral position.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-41-00
Page 543
Feb 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
5) Put the captain’s control column back to the neutral position.
(h) Position the stabilizer to an intermediate position (Approximately 8 units of trim is
satisfactory).
(i) Move and hold the STAB TRIM switches on the captain’s control wheel to the NOSE DOWN
position.
1) Make sure that the stabilizer leading edge moves up (APL NOSE DOWN).
2) While the stabilizer moves, pull the captain’s control column aft until the column cutout
switch stops the stabilizer.
3) Hold the captain’s control column in this position and immediately release the STAB
TRIM switches.
4) Use a control column assembly protractor, SPL-1680 to make sure the captain’s control
column is between 3.20 and 4.21 degrees aft from the neutral position.
5) Put the captain’s control column back to the neutral position.
SUBTASK 27-41-00-860-022
(2) Do this task: Put the Elevator Hydraulic systems A and B Back to the Condition Before the
Pressurization, TASK 27-31-00-840-801.
------------------------- END OF TASK ---------------------------
TASK 27-41-00-700-810
12. Column Cutout Switches Test
(Figure 506)
A. General
(1) Use this test to make sure the captain’s and first officer column cutout switches operate
correctly.
B. Tools/Equipment
NOTE: When more than one tool part number is listed under the same "Reference" number, the
tools shown are alternates to each other within the same airplane series. Tool part numbers
that are replaced or non-procurable are preceded by "Opt:", which stands for Optional.
Reference Description
SPL-1680 Protractor - Assembly, Control Column
(Part #: 4MIT65B80307-1, Supplier: 81205, A/P Effectivity: 737-100,
-200, -200C, -300, -400, -500, -600, -700, -700C, -700ER, -700QC, -800,
-900, -900ER, -BBJ)
(Part #: A27021-29, Supplier: 81205, A/P Effectivity: 737-100, -200,
-200C, -300, -400, -500, -600, -700, -700C, -700ER, -700QC, -800, -900,
-900ER, -BBJ)
SPL-1685 Box - Test, Cutout Switch, Stab Trim Control
(Part #: C27007-31, Supplier: 81205, A/P Effectivity: 737-300, -400,
-500, -600, -700, -700C, -700ER, -700QC, -800, -900, -900ER, -BBJ)
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 AIRCRAFT MAINTENANCE MANUAL飛機維護手冊3(120)