国产男女无遮挡_日本在线播放一区_国产精品黄页免费高清在线观看_国产精品爽爽爽

  • 熱門標簽

當前位置: 主頁 > 航空資料 > 國外資料 >

時間:2010-05-28 00:44來源:藍天飛行翻譯 作者:admin
曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

desired by ATC. If unable to obtain holding
instructions prior to reaching the fix (due to
frequency congestion, stuck microphone, etc.), then
enter a standard pattern on the course on which the
aircraft approached the fix and request further
clearance as soon as possible. In this event, the
altitude/flight level of the aircraft at the clearance
limit will be protected so that separation will be
provided as required.
2/19/04 AIM
En Route Procedures 5−3−9
d. When an aircraft is 3 minutes or less from a
clearance limit and a clearance beyond the fix has not
been received, the pilot is expected to start a speed
reduction so that the aircraft will cross the fix,
initially, at or below the maximum holding airspeed.
e. When no delay is expected, the controller
should issue a clearance beyond the fix as soon as
possible and, whenever possible, at least 5 minutes
before the aircraft reaches the clearance limit.
f. Pilots should report to ATC the time and
altitude/flight level at which the aircraft reaches the
clearance limit and report leaving the clearance limit.
NOTE−
In the event of two-way communications failure, pilots are
required to comply with 14 CFR Section 91.185.
g. When holding at a VOR station, pilots should
begin the turn to the outbound leg at the time of the
first complete reversal of the to/from indicator.
h. Patterns at the most generally used holding
fixes are depicted (charted) on U.S. Government or
commercially produced (meeting FAA requirements)
Low or High Altitude Enroute, Area and STAR
Charts. Pilots are expected to hold in the pattern
depicted unless specifically advised otherwise by
ATC.
NOTE−
Holding patterns that protect for a maximum holding
airspeed other than the standard may be depicted by an
icon, unless otherwise depicted. The icon is a standard
holding pattern symbol (racetrack) with the airspeed
restriction shown in the center. In other cases, the airspeed
restriction will be depicted next to the standard holding
pattern symbol.
REFERENCE−
AIM, Holding, Paragraph 5−3−7j2.
i. An ATC clearance requiring an aircraft to hold
at a fix where the pattern is not charted will include
the following information: (See FIG 5−3−2.)
1. Direction of holding from the fix in terms of
the eight cardinal compass points (i.e., N, NE, E, SE,
etc.).
2. Holding fix (the fix may be omitted if
included at the beginning of the transmission as the
clearance limit).
3. Radial, course, bearing, airway or route on
which the aircraft is to hold.
4. Leg length in miles if DME or RNAV is to be
used (leg length will be specified in minutes on pilot
request or if the controller considers it necessary).
5. Direction of turn if left turns are to be made,
the pilot requests, or the controller considers it
necessary.
6. Time to expect further clearance and any
pertinent additional delay information.
AIM 2/19/04
5−3−10 En Route Procedures
FIG 5−3−2
Holding Patterns
TYPICAAL PROCEDURE ON AAN ILS OUTER MAARKER
EXAMPLES OF HOLDING
L OM M M
RUNWAY
VOR
VOR
TYPICAL PROCEDURE AT INTERSECTION
OF VOR RAADIAALS
HOLDING COURSE
AWAY FROM NAVAID
HOLDING COURSE
TOWARD NAVAID
VORTAC
115 NM DME FFIIX 10 NM DME FIIX
TYPIICAL PROCEDURE AT DME FIIX
8/5/04 AIM
En Route Procedures 5−3−11
FIG 5−3−3
Holding Pattern Descriptive Terms
ABEAM
HOLDING SIDE
OUTBOUND
END
HOLDING
COURSE
OUTBOUND
INBOUND
NONHOLDING SIDE
FIX END
RECIPROCAL
FIX
j. Holding pattern airspace protection is based on
the following procedures.
1. Descriptive Terms.
(a) Standard Pattern. Right turns
(See FIG 5−3−3.)
(b) Nonstandard Pattern. Left turns
2. Airspeeds.
(a) All aircraft may hold at the following
altitudes and maximum holding airspeeds:
TBL 5−3−1
Altitude (MSL) Airspeed (KIAS)
MHA − 6,000’ 200
6,001’ − 14,000’ 230
14,001’ and above 265
(b) The following are exceptions to the
maximum holding airspeeds:
(1) Holding patterns from 6,001’ to
14,000’ may be restricted to a maximum airspeed of
210 KIAS. This nonstandard pattern will be depicted
by an icon.
(2) Holding patterns may be restricted to a
maximum airspeed of 175 KIAS. An icon will depict
this nonstandard pattern. Pilots of aircraft unable to
 
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址:AIM航空信息手冊2004上(179)
国产男女无遮挡_日本在线播放一区_国产精品黄页免费高清在线观看_国产精品爽爽爽
激情六月天婷婷| 99久久激情视频| av网址在线观看免费| 国产精品久久久久久久av电影| 亚洲a级在线观看| av一区二区三区免费| 插插插亚洲综合网| 免费看国产精品一二区视频| 国产成人精品综合| 欧美影院在线播放| 色偷偷888欧美精品久久久| 日本一区二区黄色| 国产成人一区二| 日本女人高潮视频| 久久精品xxx| 日韩av123| 久久久久久噜噜噜久久久精品| 日本久久久久久| 久久超碰亚洲| 日本精品久久中文字幕佐佐木| 国产激情片在线观看| 熟女少妇在线视频播放| 久久久综合亚洲91久久98| 日本一区二区在线免费播放| 国产成人在线一区| 日韩免费观看视频| 日韩专区在线播放| 国内精品视频久久| 久久99久久99精品中文字幕| 国产欧美中文字幕| 亚洲熟妇无码一区二区三区导航| 91免费的视频在线播放| 天天综合五月天| 国产suv精品一区二区三区88区| 日本一本草久p| 色妞久久福利网| 美女被啪啪一区二区| 国产99视频精品免费视频36| 国产精品自拍片| 亚洲一区二区三区免费看| 久久久国产精华液999999| 欧美一二三区| 精品国产一区二区三区麻豆免费观看完整版 | 色乱码一区二区三在线看| 久久久久久久久久久91| 激情视频在线观看一区二区三区| 精品国产乱码久久久久软件 | 精品国产综合| 国产精品12p| 欧美精品一区二区三区在线看午夜| 国产精品久久久久7777婷婷| 国产精品一区二区免费| 三区精品视频观看| 国产精品人人做人人爽| 成人精品一区二区三区电影免费| 亚洲成熟丰满熟妇高潮xxxxx| 日韩有码在线电影| 国产欧美123| 日韩精品无码一区二区三区| 国产精品成人观看视频国产奇米| 97免费视频观看| 欧美日韩在线观看一区| 一区二区三区欧美成人| 久久99精品国产一区二区三区 | 视频一区二区在线观看| 国产精品欧美久久久| 91精品国产高清久久久久久久久| 欧美亚洲国产日本| 一本久道高清无码视频| 久久狠狠久久综合桃花| 国产美女视频免费| 欧美又大又粗又长| 亚洲最大福利网| 国产精品美女久久久久av超清| 91精品国产综合久久久久久久久| 欧美成人蜜桃| 欧美一级淫片播放口| 九九热精品视频在线播放| 久久全国免费视频| 国产美女无遮挡网站| 欧美日韩一区二区视频在线观看 | 国产精品日韩欧美综合| 久久人人97超碰人人澡爱香蕉| 精品一区二区国产| 日本久久久久亚洲中字幕| 尤物一区二区三区| 不卡av在线网站| 久久久999国产| 久久www免费人成精品| 国产裸体写真av一区二区| 欧美精品一区二区三区在线看午夜 | 国产精品亚洲a| 蜜臀av性久久久久蜜臀av| 日韩在线xxx| 一区二区不卡在线| 精品久久久久久一区| 久久久99久久精品女同性| 8050国产精品久久久久久| 国产精品有限公司| 国产一区二区在线免费视频| 欧美日韩天天操| 日本精品性网站在线观看| 午夜精品视频在线观看一区二区 | 国产乱人伦精品一区二区三区| 欧美午夜视频在线| 人人爽久久涩噜噜噜网站| 日本欧洲国产一区二区| 亚洲va久久久噜噜噜久久狠狠| 国产精品日韩一区二区| 日韩在线观看精品| 久久久久久有精品国产| 国产成人在线亚洲欧美| 久久免费成人精品视频| 国产传媒一区二区| 久久国产一区| 久久久久久久9| 色偷偷噜噜噜亚洲男人的天堂| 国产极品粉嫩福利姬萌白酱| 久久综合精品一区| 国产高清在线精品一区二区三区| 国产精品91视频| 久久久一本精品99久久精品66| 91老司机精品视频| 99久热re在线精品996热视频| 国产精品亚洲综合| 成人福利网站在线观看| 99久久国产宗和精品1上映| 91免费黄视频| 久久视频这里有精品| 久久免费视频3| 久久久久久久一区二区| 久久久国产在线视频| 国产精品美女在线观看| 另类天堂视频在线观看| 美日韩精品视频免费看| 伊人久久大香线蕉精品| 懂色中文一区二区三区在线视频| 视频一区不卡| 欧美日韩一区在线观看视频| 加勒比海盗1在线观看免费国语版| 男女超爽视频免费播放| 国产日韩精品一区二区| 成人h视频在线观看| 国产精品10p综合二区| 日韩在线国产精品| 国产精品久久国产三级国电话系列| 久久av中文字幕| 亚洲第一综合| 欧美最猛性xxxx| 国产日韩欧美日韩| 91精品国产777在线观看| 日韩在线免费视频观看| 国产精品久久久久久久天堂第1集 国产精品久久久久久久午夜 | 国模视频一区二区三区| 国产视频一区二区三区四区| 成人在线一区二区| 国产suv精品一区二区三区88区| 久久精品99久久香蕉国产色戒| 精品毛片久久久久久| 亚洲www永久成人夜色| 青青青国产在线观看| 国产淫片免费看| av 日韩 人妻 黑人 综合 无码| 久久亚洲国产成人精品无码区| 久久精品国产亚洲精品2020| 久99久在线视频| 日韩欧美亚洲v片| 国产私拍一区| 国产传媒久久久| 欧美区在线播放| 人偷久久久久久久偷女厕 | 99精品国产一区二区| 日韩最新免费不卡| 一道精品一区二区三区| 欧洲精品久久| 99精彩视频| 国产成人精品在线观看| 亚洲综合在线中文字幕| 欧美连裤袜在线视频| 99在线视频免费观看| 国产精品入口免费| 日韩一区二区三区高清| 国产亚洲综合视频| 久久久噜久噜久久综合| 欧美激情精品久久久久久久变态| 日韩国产精品一区二区| 国产精品自产拍在线观看中文| 色琪琪综合男人的天堂aⅴ视频| 影音先锋欧美在线| 国内精品久久国产| 国产成年人在线观看| 欧美精品在线观看| 欧美在线日韩精品| 91精品国产一区| 欧美乱妇高清无乱码| 欧洲久久久久久| 久久综合入口| 亚洲免费久久| 成人毛片网站| 精品毛片久久久久久|