(a)  
Put the switch in the hole in the bottom door beam.

 (b)  
Put the locknut on the switch.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-71-01
 ALL  ú ú 12 Page 433 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (c)  
Put the lockwire on the switch.

 (d)  
Connect the wiring to the switch.

 (e)  
Adjust the door latched switch. 1) Move the switch in its bracket to get the dimension shown

 in Detail D. 2) Use a torque wrench to turn the latch actuator clockwise. 3) Monitor the torque you use to turn the actuator. 4) Turn the actuator until the torque increases 15 to 20
 pound-inches.
 NOTE: The actuator hits the internal stops.
____
 5)  Make sure you can push in the plunger of the door latched
 switch. 6) Manually turn the latch actuator 18 turns counterclockwise. 7) Make sure the plunger on the door latched switch does not
 touch the striker on the latch torque tube. 8) Disconnect the D 225E connector from the equipment module. 9) Make sure there is continuity between pins 3 and 4 on the
 DX225E connector. 10) Manually turn the latch actuator 4 turns clockwise. 11) Move the door latched switch in its bracket to make it
 operate. 12) Make sure there is no continuity between pins 3 and 4 of the DX225E connector when the switch operates. 13) Connect the DX225E connector to the side cargo door equipment module.
 S 424-143
 (3)  
Install the door closed switch.

 (a)  
Put the switch in the hole in the door beam.

 (b)  
Put the locknut on the switch.

 (c)  
Put the lockwire on the switch.

 (d)  
Connect the wiring to the switch.

 (e)  
Adjust the door closed switch.

 1)  Move the switch in its bracket to get the dimension shown in Detail E.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-71-01
 ALL  ú ú 07 Page 434 ú Oct 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 2) Disconnect the DX225E connector from the equipment module. 3) Make sure there is no continuity between pins 1 and 2 of the DX225E connector when the door is closed. 4) Connect the DX225E connector to the equipment module.
 S 864-070
 (4)  
Close these circuit breakers for the applicable EICAS system:

 (a)  
P7 Overhead Circuit Breaker Panel
 1) 7F8 UPR EICAS
 2) 7F9 EIU L
 3) 7F10 EIU C
 4) 7F14 LWR EICAS
 5) 7F15 EIU R

 S 864-057
 (5)  
Supply the electrical power (AMM 24-22-00/201).

 S 724-058

 (6)  
Do a test of the door warning system on the side cargo door.

 (a)  
Make sure the door is closed, latched and locked.

 (b)  
Do a test of the LATCHES CLOSED light. 1) See that the green LATCHES CLOSED light on the operators

 panel is off. 2) Unlock the side cargo door. 3) See that the green LATCHES CLOSED light on the door
 operators panel is on. 4) Move the latches to the not latched position.
 NOTE: You can do this manually or electrically.
____
 5)  Make sure the green LATCHES CLOSED light on the door operators panel goes off.
 (c)  
Completely open the door.

 (d)  
Make sure that the DOOR SIDE CARGO (CAUTION) message shows on EICAS.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-71-01
 ALL  ú ú 06 Page 435 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 艙門 DOORS 4(92)