the structure of the fuselage. a) Align the holes. 2) Loosely install some bolts through the skin into the nutplates on the hinge. 3) Loosely install the bolts through the hinge into the nutplates on the structure.
 4)  Loosely install the special bolts into the ends of the hinge. a) Put the countersunk washer adjacent to the head of the
 bolt
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-49-04
 ALL  ú ú 01 Page 404 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 b) Put the flat washer adjacent to the nut. 5) Loosely install the other bolts through the skin into the nutplates on the hinge. 6) Tighten all the bolts.
 S 824-018
 (2)  
Adjust the door.

 (a)  
Close but do not latch the door.

 (b)  
Use the spring scale to close the latches.

 (c)  
Make sure the latches close with a force of 5 to 10 pounds.

 1)  Change the shims below the latch if it is necessary to get the correct force (Section A-A).
 S 214-019
 (3)  
Examine the clearances around the door.

 (a)  
Make sure the clearance at the forward and the right edge of the door is from 0.04 to 0.12 inch.

 (b)  
Make sure the clearance at the aft edge of the door is from

 0.04 to 0.16 inch.
 (c)  
Remove material from the edge of the door if it is necessary to get the correct dimension.

 (d)  
If you remove material, paint the area with Alodine
 (Ref 51-21-04/701).

 (4)  
Open and close the door to make sure it operates correctly.

 S 724-020
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-49-04
 ALL  ú ú 01 Page 405 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 STABILIZER JACKSCREW ACCESS DOOR - REMOVAL/INSTALLATION
_______________________________________________________
 1. General
_______
 A. This procedure contains three tasks:
 (1)  
The removal of the access door for the stabilizer jackscrew

 (2)  
The installation of the access door for the stabilizer jackscrew.

 (3)  
The test of the access door for the stabilizer jackscrew.

 TASK 52-49-05-004-001
 2. Stabilizer Jackscrew Access Door Removal (Fig. 401)
________________________________________
 A. References
 (1)  
IPC 52-49-05 Fig. 2

 B.
Access

 (1)  
Location Zone
 312 Area Aft of Pressure Bulkhead, RH

 (2)  
Access Panel 312A Door - Access, Jackscrew Horizontal Stabilizer

 C.
Procedure

 S 014-002
 (1)  
Open the door.

 S 024-003

 (2)  
Remove the door.

 (a)  
Disconnect the stay brace at the door. 1) Pull the cotter pin from the pin in the stay brace. 2) Pull the pin out of the clevis. 3) Make a note of the radial location of the clevis.

 NOTE: This makes the subsequent installation easier.
____
 (b)  
Remove the hinge pin bolts (Detail C).

 (c)  
Identify the location of the radius fillers with tags.

 NOTE: It is necessary to know the correct location of
____ the fillers during the subsequent installation.
 TASK 52-49-05-404-004
 3. Installation of the Stabilizer Jackscrew Access Door (Fig.____________________________________________________401)
 A. Consumable Materials
 (1)  
C00523 Coating - Alodine, MIL-C-5541

 (2)  
D00013 Grease, MIL-G-23827

 B.
References

 (1)  
51-21-04/701, Alodized Surfaces

 (2)  
IPC 52-49-05 Fig. 2

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 艙門 DOORS 4(53)