applicable roller stop.
 7) Open the door.
 8) Remove the roller stops.
 9) Put washers on the roller stops.

 NOTE: The washers change the location of the roller
____ stops. This puts a load on the latch.
 a) Add 0.018 inch to the dimension you measured between the roller stop and the roller.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-49-05
 ALL  ú ú 01 Page 410 ú Jun 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 b) Get washers that are as thick as this sum.
 c) Install the washers on the roller stop. 10) Install the roller stops. 11) Put the lockwire on the bolt in the roller stop.
 (g)  
Attach the G52015 tool to the door.

 (h)  
Do the complete test of the stabilizer jackscrew access door again.

 S 094-024
 (12)
 Remove the G52015 tool from the airplane.

 S 864-025

 (13)
 Close the door.

 (14)
 Remove the maintenance stand.

 S 094-026
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-49-05
 ALL  ú ú 01 Page 411 ú Oct 10/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 STABILIZER JACKSCREW ACCESS DOOR - INSPECTION/CHECK
___________________________________________________
 1.  General_______
 A.  This procedure contains a task that examines the hinges on the access door for the stabilizer jackscrew.
 B.  You must remove the access door to do this procedure.
 TASK 52-49-05-206-001
 2.  Stabilizer Jackscrew Access Door Inspection (Fig. 601)___________________________________________
 A.  References
 (1)  
52-49-05/401, Stabilizer Jackscrew Access Door

 (2)  
IPC 52-49-05 Fig. 2

 B.  
Access

 (1)  
Location Zone
 312 Area Aft of Pressure Bulkhead, RH

 (2)  
Access Panel 312A Door - Access, Jackscrew Horizontal Stabilizer

 C.  
Procedure

 S 026-005
 (1)  
Remove the access door for the stabilizer jackscrew (Ref 52-48-01/401).

 S 226-006

 (2)  
Measure the fits of the hinge pins and the hinge arms.

 (a)  
Measure the parts at the locations shown in figure 601.

 (b)  
Compare the measured dimensions to the wear limits in figure

 601.

 (c)  
If a part is not in tolerance, replace the part if you cannot repair it.

 S 426-007
 (3)  Install the access door for the stabilizer jackscrew (Ref 52-49-05/401).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-49-05
 ALL  ú ú 01 Page 601 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

SEE A
SEE B
FWD
A
Stabilizer Jackscrew Access Door Wear Limits Figure 601 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-49-05
 ALL  ú ú 01 Page 602 ú Oct 10/89
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

COTTER PIN 
NUT 
A 
HINGE ARM 
HINGE FITTING 
RADIUS FILLER HINGE PIN  A  B  1.  HINGE HALF/PIN 

A-A 
1 INDEX NO.  PART NAME HINGE HALF HINGE PIN  DIM. ID OD  DIAMETER DESIGN LIMITS MIN MAX 0.2500 0.2430 0.2515 0.2450  DIAM CLEAR-ANCE WEAR DIM. MAX WEAR LIMITS ALLOWED 0.2620 0.2330 0.017  REPLACE PART WORN X X  REPAIR WORN PART  REPAIR INSTR. 
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機(jī)維護(hù)手冊(cè) 艙門 DOORS 4(57)