(d)  
Keep the spacers that are in the hinge in the center.

 (e)  
Pull the door away from the fuselage.

 TASK 52-48-01-404-005
 3. Air Conditioning Access Door Installation (Fig. 401)
_________________________________________
 A. Standard Tools and Equipment
 (1)  
Bonding Meter (Ref 20-22-01/601)

 B.
References

 (1)  
20-22-01/601, Electrical Bonding

 (2)  
51-24-03/701, Conductive Coating System for Exterior Fiberglass

 (3)  
IPC 52-48-01

 C.
Access

 (1)  
Location Zone
 133 Air Conditioning Equipment Bay Left
 134 Air Conditioning Equipment Bay Right

 (2)  
Access Panel
 191AL Door - Air Conditioning Access
 191EL Panel - Air Conditioning Access
 191HL Door - Air Conditioning Access
 191ML Panel - Air Conditioning Access
 191NL Door - Air Conditioning Access
 192AR Door - Air Conditioning Access
 192ER Panel - Air Conditioning Access
 192HR Door - Air Conditioning Access
 192MR Panel - Air Conditioning Access

 D.
Procedure

 S 014-006
 (1)  If it is necessary, remove the covers from the forward edge of the hinges.
 NOTE: There are not covers on the hinges of the aft, left,
____
 outboard door.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-48-01
 ALL  ú ú 01 Page 404 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
 (2)  S 844-017Prepare the door for installation. (a) Clean the areas around the fastener holes. (b) Make sure the bonding jumpers attach to clean areas. 1) Look at the areas where the bonding jumpers attach. 2) If it is necessary, clean the areas where the bonding jumpers attach (Ref 51-24-03/701).
 (3)  S 424-008Install the door. (a) Put the door in the opening. (b) Install the hinge pins in the hinges. 1) Put a washer on the hinge pin. 2) On the hinge in the center of the door, put the spacers between the segments of the hinge. 3) Push the hinge pin through the aft end of the hinge fitting.
 NOTE:____ The head of the pin points aft.
 4) 5) 6)  Put a washer on the aft end of the hinge pin.Put a nut with castellations on the hinge pin.Do not install a cotter pin in the hinge pin at this time.
 (4)  S 824-009Adjust the door. (a) Close but do not latch the door. (b) See that the contour of the door aligns with the contour of the fuselage between -0.03 and +0.10 inch. (c) Measure the clearances around the door shown in Fig. 402. 1) Change the shims below the hinges if it is necessary to get the correct clearances. 2) On a new door, remove material from the edges of the door to get the clearances, if it is necessary.
 (5)  S 014-018Open the door.
 (6)  S 434-019Install cotter pins on the hinge pins.
 (7)  S 714-020If the new door has latches, do a check of the latches.
 NOTE:____ This is to show that there is not a load on the latches.
 (a) (b)  Close but do not latch the door.Push at the latch until the the door aligns with the fuselage between -0.03 and +0.10 inch.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-48-01
 ALL  ú ú 01 Page 405 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

747-400
MAINTENANCE MANUAL

EE

B

FF
LOCATION DIMENSION

FWD

Bottom View of Air Conditioning Doors To Show Clearances
Figure 402

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-48-01
 ALL  ú
 ú  01  Page 406
 ú  Feb 10/91 

BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 艙門 DOORS 4(34)