MAIN ELECTRONIC EQUIPMENT
COMPARTMENT 
SEE  A 
CENTER ELECTRONIC 
EQUIPMENT  SWITCH 
COMPARTMENT  PLUNGER 
SEE  B 

SWITCH ACTUATORLOCKNUT (1 EACH SIDE)
A
LATCH  A  MAIN ELECTRONIC EQUIPMENT COMPARTMENT 
FITTING  ACCESS DOOR WARNING SWITCH
A 
BOLTS  SWITCH 
PLUNGER WITH 
THE DOOR IN THE

CENTER ELECTRONIC EQUIPMENT COMPARTMENT
OPEN POSITION
ACCESS DOOR WARNING SWITCH
0.12 INCH 0.51 INCH
B
MINIMUM SWITCH PLUNGER MOVEMENT
SWITCH LOCKNUT (2 LOCATIONS) LATCH PIN
MOUNTINGLOCKWASHER
BRACKET KEYING WASHER
A-A
Electronic Equipment Door Warning Switch Adjustment Figure 503
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-71-00
 ALL  ú ú 04 Page 531 ú Feb 10/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (b)  Move the switch in the bracket until the DOOR ELEC MAIN message shows on the EICAS display.
 NOTE: Keep the locknuts finger tight against the bracket.
____
 (c)  As an option, do these steps to measure the continuity of the switch with an ohmmeter: 1) Disconnect the DW2679C connector at the E2-6 disconnect
 rack. 2) Connect an ohmmeter between pin C4 and ground. 3) Move the switch in the bracket until there is no continuity
 from pin C4 to ground.
 NOTE: Keep the locknuts finger tight against the bracket.
____
 (d)  Turn the 2 locknuts two more complete turns to allow the switch plunger to be further depressed in the switch.
 NOTE: You can turn the locknuts two more turns after the
____ initial two turns to provide additional plunger depression. If you cannot turn the locknuts a total of four turns then turn them as much as the threads on the plunger will allow.
 (e)  
Tighten the locknuts.

 (f)  
Safety the locknuts with wire.

 (g)  
Do these steps if you used an ohmmeter to adjust the switch: 1) Remove the ohmmeter from the connector. 2) Connect the DW2679C connector to the E2-6 disconnect rack.

 (h)  
Do a test of the warning switch for the main electronic equipment compartment. 1) Make sure the door is open. 2) Make sure the message DOOR ELEC MAIN shows on EICAS. 3) Close the door. 4) Make sure the message DOOR ELEC MAIN does not show on

 EICAS.
 S 825-021
 (9)  
Adjust the warning switch on the access door to the center electronic equipment compartment (Fig 503).

 (a)  
Move the switch in the bracket to get the 0.51 inch dimension shown in Section A-A.

 (b)  
Close and latch the access door.

 (c)  
Make sure the door latch pin pushes the switch plunger more than 0.12 inch.

 (d)  
Safety the locknuts with wire.

 (e)  
Do a test of the warning switch for the center electronic equipment compartment. 1) Make sure the door is open. 2) Make sure the message DOOR ELEC CTR shows on EICAS. 3) Close the door.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-71-00
 ALL  ú ú 06 Page 532 ú Feb 10/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 4) Make sure the message DOOR ELEC CTR does not show on EICAS.
 S 825-079
 (10)
 It is not possible to adjust the door closed switches or the switches in the latches on the nose cargo door.

 (a)  
Put lockwire on the locknuts of the door closed switches.

 S 825-080
 (11) Adjust the warning switch on the upper deck crew service door (Fig. 505).
 (a)  Open the door.
 (b)  Turn the switch plunger clockwise until it hits the mechanical
 stop.
 (c)  Turn the switch plunger counterclockwise one-half turn at a
 time until the message DOOR R UPR DK shows on EICAS.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 艙門 DOORS 4(78)