EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-11-13
 ALL  ú ú 03 Page 401 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 D. Prepare for Removal
 S 014-002
 (1)  
Remove the entry door lining (Ref 52-11-02/401).

 S 014-005

 (2)  
Remove the access panel (1) on the hinge torque tube and the cam access cover (3) from the door structure.

 E.
Procedure

 S 034-006
 (1)  Remove the stub shaft (30) and the shims (29), if installed.
 NOTE: Keep the shims for the installation.
____
 S 034-007
 (2)
Remove the control cam (28, Detail A) from the inner shaft (24).

 S 034-008

 (3)  
Remove the upper and lower control rods (41, 86, Detail E) from the inner latch crank (87).

 NOTE: Turn the handle shaft, if it is necessary, to align the crank
____
 ends with the access holes in the housing.

 S 034-009
 (4)  
Disconnect the pushrod (20) from the hinge torque tube.

 S 034-032

 (5)  
Disconnect the disarm cable from the dangler brace (59)
 (Detail B, Door 1; Detail C, Door 5).

 S 024-011

 (6)  
Do these steps to remove the external handles (9) and the center shaft (45) from the handle mechanism housing (21) (Detail A, Fig. 401 ):

 NOTE: You can remove the basket cam (49) from the housing as a part
____ of the external handles and the center shaft assembly (45), if it is necessary.
 (a)  Remove the control cam (28) from the splines on the inner shaft (24).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-11-13
 ALL  ú ú 03 Page 402 ú Feb 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

41. UPPER CONTROL ROD 
A  1. HINGE TORQUE PANEL TUBE ACCESS 
SEE A 5. HANDLE MECHANISM  A  2. BOLT (21 LOCATIONS) 
4. BOLT (4 LOCATIONS) 
3. CAM ACCESS COVER 
86. LOWER CONTROL ROD 
NOTE: DOOR 1 SHOWN, OTHER DOORS EQUIVALENT.____  FWD 

Main Entry Door Handle Mechanism Installation
Figure 401 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-11-13
 ALL  ú ú 01 Page 403 ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

8. CAM FOLLOWER BEARING
7. WASHER
6. BOLT  SEE F
9. EXTERNAL HANDLE
57. BOLT
10. COVERPLATE (3 LOCATIONS)
56. WASHER (3 LOCATIONS)
11. BOLT (4 LOCATIONS)
55. BEARING RETAINER 58. LAMINATED
7. WASHER (3 LOCATIONS) SHIM
54. PACKING
12. NUT SEAL
45. CENTER SHAFT 13. PEDESTAL
53. LAMINATED SHIM 46. PACKING 14. PIVOT SPACER 48. OUTER 15. DANGLER (2 EACH PEDESTAL)SHAFT52. SPANNER
44. SPACER NUT 47. BEARING 16. YOKE (2 LOCATIONS)
THRUST (DO NOT REMOVE COLLAR FROM HOUSING 49. BASKET CAM 43. WASHER
EXCEPT FOR  SEE B 50. SEAL WASHER REPLACEMENT
(3 LOCATIONS)  (DOORS 1)
OR NECESSARY 42. BOLT SEE CADJUSTMENTS)51. BEARING (DOOR 5)SPACER 17. NUT
41. UPPER CONTROL ROD 18. YOKE
LATCH CRANK
SEE D
19. SPRING
40. SPACER DEPRESSOR
38.
 LAMINATED SHIM

39.
 YOKE ATTACHMENT

NUT 
36. WASHER 
(4 LOCATIONS) 
35. BOLT  23. SPRING 
(4 LOCATIONS)  24. INNER  20. COCKING 
SHAFT  PUSHROD 
33. NUT 34. WASHER  25. YOKE 26. CLUTCH THRUST WASHER  22. COCKING SEE D CRANK  SEE 21. HANDLE MECHANISM  D 
COLLAR  HOUSING 
27. SUPPORT  SEE  E 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 艙門 DOORS 1(98)