(g)  
If the distance and the torque are satisfactory, no adjustment is necessary.

 (h)  
If the distance and the torque are not satisfactory, do these steps:

 NOTE: One-half turn of the gate pushrod changes the unlatching
____ torque by 50 to 100 pound-inches (2.75 to 5.55 pounds on the spring scale).
 ~.............................................................. |CONDITION |ADJUSTMENT | ................................................................
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-11-09
 ALL  ú ú 06 Page 519 ú Jun 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 |Both the torque and |Make the upper gate pushrod and | |the distance are less |the upper latch pushrod longer | |than the satisfactory | | |amount | | ................................................................ |The torque is less than |Make the upper gate pushrod | |the satisfactory amount; |longer | |the distance is | | |satisfactory | | ................................................................ |The torque is more than |Make the upper gate pushrod | |the satisfactory amount; |shorter | |the distance is | | |satisfactory | | ................................................................ |The torque is satisfactory; |Make the upper gate pushrod | |the distance is less than |shorter and make the upper | |the satisfactory amount |latch pushrod longer | ................................................................ |Torque is satisfactory; |This is an acceptable condition | |the distance is more than |no adjustment is necessary | |the satisfactory amount | | 2.............................…................................1
 (i)  
Slowly latch the door with the torque wrench (or spring scale).

 (j)  
Make sure the latching torque is not more than 540 pound-inches (30 pounds on the spring scale).

 (k)  
Do these steps if the latching torque is not satisfactory: 1) Make the upper gate pushrod shorter. 2) Measure the unlatching torque again to make sure it stays

 satisfactory.
 S 825-017
 (7)  Make sure the following adjustments are satisfactory:
 NOTE:____These adjustments are related. When you change one of them, you must continue to check and change the other adjustments until they are all satisfactory. Refer to the appropriate steps to make these adjustment.
 (a)  
The clearance between the latch roller and the latch fitting (4 locations)

 (b)  
The flushness of the door skin and body skin

 (c)  
The handle torque

 (d)  
The upper and lower gate overcenter dimension

 (e)  
Remove the ruler from the door structure.

 S 225-018
 (8)  
Do a check of the blade seal (Fig. 503) (Ref 52-09-02/201).

 (a)  
Make sure the door is closed and latched.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-11-09
 ALL  ú ú 06 Page 520 ú Oct 10/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (b)  Make sure the blade seal is as shown in Fig. 503.
 S 825-019
 (9)  
Adjust the door centering guide.

 (a)  
Install the door centering guide on the door.

 (b)  
Move the centering guide to get the clearances shown in Fig. 501, Detail E. 1) Change the washers on the guide attachment to move it

 forward or aft. 2) Move the guide on the serrated plate to move it up or down.

 (c)  
Tighten the nut on the centering guide shaft to keep the guide from turning.

 S 825-020
 (10)
 Adjust the hold-open device (Detail G).

 (a)  
Fully open the door.

 (b)  
Push 10 to 15 pound force inboard on the door to take the play out of the hold-open device.

 (c)  
Make sure the forward edge of the door is 4 to 6 inches from the body skin.

 (d)  
Adjust the anchor plate if it is necessary to move the forward edge of the door. 1) Loosen the four anchor plate attach bolts to adjust the
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 艙門 DOORS 1(76)