B.  
Consumable Materials

 (1)  
Grease - MIL-G-23827

 (2)  
Solvent - Acetone (O-A-51) or Methyl Ethyl Ketone (TT-M-261)

 (3)  
Primer, Chemical and Solvent Resistant - BMS 10-11, Type I

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. FREIGHTERS ú

 52-11-02
 ú CONFIG ú 02 Page 401 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

LINING ATTACHMENT LINING
SPACER SCREW SUPPORT
LINING) CHANNEL
LINING SUPPORT
LINING
A-A
Main Entry Door Lining Figure 401 (Sheet 1)

LINING
LINING ATTACHMENT SCREW
LINING
B-B
C76880
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. FREIGHTERS ú

 52-11-02
 ú CONFIG ú 02 Page 402 ú Oct 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

D-D
Main Entry Door Lining Figure 401 (Sheet 2)
C76838
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. FREIGHTERS ú

 52-11-02
 ú CONFIG ú 02 Page 403 ú Oct 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 C.  Access
 (1)  
Access Panels
 831L Door - No. 1 Main Entry, LH
 835L Door - No. 5 Main Entry, LH

 D.  
Procedure

 S 424-005-002
 (1)  
For the upper or lower lining, do this step:

 (a)  
Install the lining on its support with the attachment screws, washers and nuts.

 S 424-006-002
 (2)  
For the center lining, do these steps:

 (a)  
Install the lining on its support with the window reveal seal in contact with the window edges.

 (b)  
Make sure the applicable cutouts in lining align with the stub shaft for the interior handle and the attachment points for the assist handle.

 (c)  
Install the lining attachment screws, washers and nuts.

 (d)  
Install the interior handle (Section C-C). 1) Apply thin coat of grease in the handle pin hole in the

 stub shaft. 2) Make sure the door is closed and latched. 3) Install the interior handle in the fully closed position
 (forward) on the stub shaft. 4) Align the interior handle with the stub shaft and install the handle pin. 5) Clean the retainer plugs with solvent and dry it with an
 air blower, if it is possible. 6) Make sure there is no remaining solvent on the plugs. 7) Put the threads of the retainer plugs in primer. Install
 and tighten the retainer plugs immediately.
 (e)  Install the assist handle (section D-D). 1) Install the handle nuts on the handle supports with the shims, collars, screws and nuts.
 2)  Put the handle on the handle nuts and tighten the nuts counterclockwise with the spanner wrench.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. FREIGHTERS ú

 52-11-02
 ú CONFIG ú 01 Page 404 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 MAIN ENTRY DOOR HINGE ARMS - REMOVAL/INSTALLATION
_________________________________________________
 1.  General_______
 A.  This procedure contains two tasks. The first task is the removal of the upper and lower hinge arms on the main entry door. The second task is the installation of the upper and lower hinge arms on the main entry door.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 艙門 DOORS 1(46)