(f)  
Make sure there is no force on the bolt.

 (g)  
Do the adjustment again, if it is necessary to get the zero force (plus-or-minus 3/4-turn of the rod end bearing will align the rod end).

 S 724-024
 (4)
Do a functional test of the handle mechanism (Ref 52-11-13/501).

 H.
Put the Airplane Back to Its Serviceable Condition

 S 414-026
 (1)  
Install the access panel (1) on the hinge torque tube and the cam access covers (3) on the door structure.

 (2)  
Install the entry door lining (Ref 52-11-02/401).

 S 414-028
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-11-13
 ALL  ú ú 03 Page 426 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 MAIN ENTRY DOOR HANDLE MECHANISM ASSEMBLY - ADJUSTMENT/TEST
___________________________________________________________
 1.  General_______
 A.  This procedure contains two tasks. The first is the test of the clutch engagement on the external handle. The second is the adjustment of the clutch engagement on the external handle.
 B.  The test will help you to find the worn effects on the clutch engagement after the handle mechanism replacement. If there is a problem with the external handle when you operate, you can use this procedure to adjust the handle mechanism.
 TASK 52-11-13-705-001
 2.  Handle Mechanism Assembly Test (Fig. 501)______________________________
 A.  Access
 (1)  
Location Zone
 211 Main Deck, Nose to First Door, LH
 271 Main Deck, Sta 2040 to Sta 2360, LH

 (2)  
Access Panel
 831L Door - No. 1 Main Entry, LH
 835L Door - No. 5 Main Entry, LH

 B.  
Procedure

 S 725-002
 (1)  
Do a test for the clutch engagement.

 (a)  
Do a visual check to make sure the bearing that holds the outer shaft (27) does not move in the cam (25).

 (b)  
Pull and turn the external handles (2, 28) until one of the bearings (3) moves on the edge of the cam (25).

 (c)  
Measure the distance between the outboard end of the center shaft (30) and the plane of the door outer contour.

 (d)  
Put the external handles (2, 28) in their positions.

 (e)  
Turn the internal handle a minimum of 40 degrees to prevent the clutch collar (15) engages with the slot on the center shaft (30).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-11-13
 ALL  ú ú 04 Page 501 ú Feb 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

SEE A HANDLE MECHANISM  A  HANDLES BASKET CAM EXTERNAL 
A 

FWD
Main Entry Door Handle Mechanism Adjustment Figure 501 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-11-13
 ALL  ú ú 01 Page 502 ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
3. CAM FOLLOWER BEARING
SEE B 2. EXTERNAL HANDLE
1. PEDESTAL
4. COVERPLATE
BOLT (4 LOCATIONS)
BOLT WASHER (3 LOCATIONS)
WASHER BEARING
BOLT RETAINER
(3 LOCATIONS) (3 LOCATIONS) SPACER
6. PEDESTAL
24. PACKING SEAL WASHER
SEAL (3 LOCATIONS)
30. CENTER SHAFT
NUT
22. LAMINATED PACKING
SHIM
27. OUTER WASHER
21. SPANNER  SHAFT NUT SPACER
26. LAMINATED SHIM
5. DANGLER  7. THRUST COLLAR 
23. BEARING 25. BASKET CAM  28. EXTERNAL HANDLE  29. SLIDE STUD 
SPACER  8. YOKE 

9. SPRING DEPRESSOR20. HOUSING
19. LATCH CRANK 10. COCKING CAM FOLLOWER BEARING CRANK
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 艙門 DOORS 1(107)