52-11-13
 ALL  ú ú 03 Page 421 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 2)  If the center shaft movement is not satisfactory, do these steps to adjust the shim (58): a) Remove the handles and the center shaft to get access
 to the shim (58). b) Decrease the laminated shim, if it is necessary. c) Temporarily install the center shaft without the
 support fitting. 3) Make sure the clearance between the cam follower bearing (8) and the edge of the basket cam (49) is at least
 0.005 inch (Fig. 401, Section A-A).
 NOTE: Use washers and shim as required to keep the
____ mounting screws square to the external handle and the cam follower bearing support. Adjust shim and washers to achieve the minimum 0.005 inch gap as shown in Section A-A.
 Make sure the screw ends are flush with the cam follower bearing support within +/- 0.02.
 S 824-020
 (4)  
If you only removed the handles (9) and center shaft (45), do a test of the handle mechanism to see if the clutch engages correctly (Ref 52-11-13/501).

 S 824-031

 (5)
If you replaced the handle mechanism, adjust the handle mechanism.

 G.  
Adjust Handle Mechanism (Fig. 402).

 NOTE: This adjustment is not necessary if you only removed the external
____
 handles (9) and the center shaft (45) (Fig. 401).

 S 824-021
 (1)  
Adjust the housing (21) for the external handle fairing and
 flushness.

 (a)  
Make sure the latch assembly (8) will not cause a blockage to the external handle (3) in the door recess. 1) If it is necessary, temporarily remove the latch keeper (1)

 from each handle (Fig. 402).

 (b)  
Hold the external handles (9, View A, Fig. 401) against the cam (49) and measure the fairing contour of the handles (View A-A, Fig. 402). 1) Make sure the handles are parallel to the door outer

 contour by less than | 0.03 inch.
 NOTE: It is satisfactory at this point if the handles are
____ parallel to the door outer contour.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-11-13
 ALL  ú ú 03 Page 422 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

THE DOOR SKIN CONTOUR
Main Entry Door Outboard Handle Latch Adjustment Figure 402
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-11-13
 ALL  ú ú 03 Page 423 ú Feb 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
 (c)

(d)

(e)

A
747-400 MAINTENANCE MANUAL
If the handles are not parallel, do these steps to adjust the laminated shim (58): 1) Remove the external handles, center shaft (45), and basket
 cam (49) to get access to the shims (53 and 58)
 2)  Remove the laminated shim (58) and adjust the shim thickness to make the handles parallel to the door outer contour.
 NOTE: Keep the minimum shim thickness.
____
 3)  Install the external handles (9), center shaft (45), and
 basket cam (49) in the housing (21) (Ref Par. F.(2).).Fully extend the external handles (9). 1) Make sure the outboard end of the center shaft (45) moves a
 minimum distance of 0.55 inch.
 NOTE: Measure this distance while you move the handles
____ from its position to the fully extended position.
 2)  If the center shaft movement is not satisfactory, do these steps to adjust the shim (58): a) Remove the handles and the center shaft to get access
 to the shim (58). b) Decrease the laminated shim, if it is necessary. c) Temporarily install the center shaft without the
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 艙門 DOORS 1(105)