32-14-05
 ALL  ú ú 01 Page 404 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 B. Parts ~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 401 | 1 |Inboard Door (LH) | 32-14-05 | 01 | 145 | | | |Inboard Door (RH) | | | 150 | | | 2 |Washer | | | 110 | | | 3 |Bolt | 32-14-05 | 02 | 120 | | | 4 |Bonding Jumper | 32-14-05 | 01 | 115 | | | 5 |Cotter Pin | | | 120 | | | 6 |Nut | | | 140 | | | 7 |Washer | | | 135 | | | 8 |Washer | | | 130 | | | 9 |Bolt | | | 125 | | | 10 |Bolt | 32-14-05 | 02 | 190 | | | 11 |Nut | 32-14-05 | 01 | 55 | | | 12 |Washer | | | 35 | | | 14 |Washer | | | 30 | | | 15 |Bolt | | | 10 | | | 18 |Bolt | 32-14-05 | 02 | 160 | | | 19 |Bolt | 32-14-05 | 02 | 155 | | | 20 |Bolt | 32-14-05 | 02 | 195 | | | 23 |Bushing | 32-14-05 | 01 | 20 | | | 24 |Flanged Bushing | 32-14-05 | 02 | 260 | | | 25 |Flanged Bushing | | | 255 | 2......…........…...................................…..........…......…........1
 C. References
 (1)
AMM 32-00-30/201, Landing Gear Door Locks

 (2)
AMM 32-14-00/501, Body Gear Doors

 (3)
AMM 32-14-05/601, Body Gear Shock Strut Inboard Door

 D.
Access

 (1)  
Location Zone
 751 Body Landing Gear Door, Aft Inboard, LH
 761 Body Landing Gear Door, Aft Inboard, RH

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-14-05
 ALL  ú

 ú 01 Page 405 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 E.  Procedure
 S 224-006
 (1)  
Do a check of the worn parts and the fittings for the approved worn areas (AMM 32-14-05/601).

 S 424-007

 (2)  
Install the inboard door.

 (a)  
Set the door (1) with the sling assembly for installation.

 (b)  
Install the bolts (9) and the washers (7 and 8) (Details B and C).

 (c)  
Engage the minimum quantity of the nut (6) to install the cotter pin (5).

 (d)  
Use the minimum washer to keep the positive clearance of 0.01 -

0.06 inch below the nut.
 (e)  
Install the bonding jumper (4) with the washers (2) and the bolts (3 , 10(two locations), and 19).

 (f)  
Connect the linkage rod to the door (Detail D).

 1)  Install the bolt (15) with the washers (12 and 14) , the nut (11) and the bushing (23).
 NOTE: Install the bolt with the head on the top part
____ of the clevis. Make sure the bushings (24 and 25) are in the clevis before you install the bolt.
 S 824-008
 (3)  Adjust the inboard door (AMM 32-14-00/501).
 NOTE:____It is not necessary to adjust the wheel well doors. The airplane must be on jacks when the gear is cycled to adjust the inboard door. The linkage rod is sensitive to all turns of the rod end. When the gear is cycled, examine the rod end and the clevis for the smooth movement.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-14-05
 ALL  ú ú 01 Page 406 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 094-013
 WARNING:_______ YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO REMOVE THE
 DOOR LOCKS FROM THE LANDING GEAR DOORS.  THE DOORS CAN CLOSE
 QUICKLY IF YOU DO NOT REMOVE THE DOOR LOCKS CORRECTLY.  THIS

 CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (4)  
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 3(91)