32-13-15
 ALL  ú ú 01 Page 602 ú Jun 10/88
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

INDEX NO.  PART NAME  DIM.  DESIGN LIMITS  WEAR LIMITS  PART REPLACE WORN  REPAIR WORN PART  REPAIR INSTR. 
DIAMETER  DIM. WEAR PER-MITTED 3  DIAM CLEAR-MAX ANCE
MIN  MAX 
1  BUSHING  ID  0.875  0.879  0.8790  0.0049  X 
BUSHING 1  OD  0.873  0.874  0.8710  X 
2  BUSHING  ID  0.750  0.751  0.7535  0.0047  X 
BOLT  OD  0.748  0.749  0.7465  X  2 
3  BEARING  ID  0.7495  0.7500  X 
BOLT  OD  0.7480  0.7490  X  2 
4  BUSHING  ID  1.000  1.001  1.006  0.008  X 
BUSHING  OD  0.997  0.998  0.995  X 
5  BUSHING  ID  0.876  0.877  0.880  0.0059  X 
BOLT  OD  0.873  0.874  0.871  X  2 
6  BEARING  ID  0.8745  0.8750  0.878  0.0039  X 
BOLT  OD  0.873  0.874  0.871  X  2 

CLAMP UP BUSHING.
REFER TO OVERHAUL MANUAL.
LLIMITS SHOWN MAY BE EXCEEDED PROVIDED MAXIMUM CLEARANCE IS NOT EXCEEDED.

Body Gear Truck Positioning Actuator Wear Limits
Figure 601 (Sheet 2)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-13-15
 ALL  ú ú 01 Page 603 ú Jun 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 BODY GEAR TRUCK POSITIONING PRESSURE REDUCING VALVE -
_____________________________________________________ REMOVAL/INSTALLATION
____________________
 1. General
 A. This procedure has two tasks:
 (1)  
The removal of the positioning pressure reducing valve (referred as the pressure valve) for the body gear truck.

 (2)  
The installation of the pressure valve for the body gear truck.

 TASK 32-13-16-004-001
 2.  The Body Gear Truck Positioning Pressure Reducing Valve Removal (Fig. 401)______________________________________________________________
 A. References
 (1)  
09-11-00/201, Towing

 (2)  
29-11-00/201, Main Hydraulic Supply System

 (3)  
32-00-30/201, Landing Gear Door Locks

 (4)  
32-13-15/401, Body Gear Truck Positioning Actuator

 (5)  
IPC 32-13-16 Fig. 1

 B.
Access

 (1)  
Location Zone
 755 Body Landing Gear, LH
 765 Body Landing Gear, RH

 C.
Prepare for the procedure

 S 844-024
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO INSTALL
_______ THE DOOR LOCKS ON THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT INSTALL THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (1)  
Do this task: "Installation of the Door Locks on the Wing Landing Gear" (Ref 32-00-30/201).

 S 844-025

 (2)  
Do this task: "Installation of the Door Locks on the Body Landing Gear" (Ref 32-00-30/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-13-16
 ALL  ú ú 01 Page 401 ú Jun 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
1480 BULKHEAD
SEE A
(RIGHT SIDE ONLY)
(LEFT SIDE ONLY)
(LEFT SIDE SHOWN
RIGHT SIDE OPPOSITE)
(STATION 1480 BULKHEAD)

A
1480 BULKHEAD
MOUNTING BOLTS
PRESSURE RELIEF VALVE
B
Body Gear Truck Positioner Pressure Reducing Valve Figure 401
HYDRAULIC FUSE
TRUCK POSITIONING PRESSURE REDUCING VALVE
SEE B
UP FWD
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 3(41)