(f)  
If the part is not in tolerance, repair or replace the part when it is necessary.

 S 426-004
 (3)  Install the wheel truck for the body landing gear (Ref 32-13-11/401).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-13-11
 ALL  ú ú 01 Page 601 ú Jun 10/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

747-400
MAINTENANCE MANUAL

SEE A
1 B
B A
CC
A
A
1 FOR LOWER TORSION LINK INSPECTION/CHECK, REFER TO 32-13-14/201
Body Gear Wheel Truck Wear Limits Figure 601 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-13-11
 ALL  ú ú 01 Page 602 ú Jun 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

1. BUSHING/PIVOT PIN

Body Landing Gear Wheel Truck Wear Limits
Figure 601 (Sheet 2)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-13-11
 ALL  ú ú 01 Page 603 ú Jun 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

WEAR LIMITS REFER TO 32-45-03/801
Body Gear Wheel Truck Wear Limits Figure 601 (Sheet 3)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-13-11
 ALL  ú ú 01 Page 604 ú Oct 10/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

INDEX NO.  PART NAME  DIM.  DESIGN LIMITS  WEAR LIMITS  REPLACE PART WORN  REPAIR WORN PART  INSTR REPAIR 
DIAMETER  DIM. WEAR MITTED PER-4  CLEAR-ANCE MAX DIA 
MIN  MAX 
1  BUSHING  ID  4.5000  4.5015  4.5057  0.0077  X 
PIN  OD  4.4980  4.4990  4.4938  X  9 
2  BUSHING  ID  0.8780  0.8790  1.2532  X 
BUSHING  OD  0.8730  0.8740  1.2448  X 
3  BUSHING  ID 
BUSHING  OD  6.1970  6.1990  6.1920  X 
4  SLEEVE 10  ID  5.1245  5.1255  3  X 
AXLE  OD  5.1275  5.1290  5.1260  X 
5  SLEEVE 10  ID  5.4945  5.4955  3
AXLE  OD  5.4975  5.4990  5.4960  X 
6  BUSHING 10  ID  5.7160  5.7170  3
AXLE  OD  5.7185  5.7195  5.7180  X 
7  BUSHING 10  ID  5.7495  5.7510  3 
AXLE  OD  5.7525  5.7530  X  8 
8  BUSHING  ID  5.7250  5.7320  3 
AXLE  OD  5.7525  5.7530  5.7520 
9  BUSHING  5  11.2490  11.2550  11.2670  7 0.0240 
BUSHING  6  11.2430  11.2480  11.2310  X  8 

INTERFERENCE FIT LIMITS SHOWN MAY BE EXCEEDED PROVIDED MAXIMUM CLEARANCE IS NOT EXCEEDED DISTANCE BETWEEN BUSHING FLANGES DISTANCE ACROSS BUSHING FLANGES MAXIMUM AXIAL CLEARANCE FOR IN SERVICE REPAIR, INSTALL SPECIAL SHIM (REF 32-00-01/801); PREFERRED
OVERHAUL REWORK IS TO RESTORE PART TO DESIGN LIMITS USING NEW BUSHINGS PART IS REPAIRABLE. REFER TO OVERHAUL MANUAL FOR REPAIR INFORMATION
YOU MUST REMOVE THIS PART TO MEASURE THE NECESSARY DIMENSIONS (REF 32-13-26/401).
Body Landing Gear Wheel Truck Wear Limits
Figure 601 (Sheet 4)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 3(30)