曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 deflector assembly to the upper tripod brace.
 NOTE: Tighten all bolts.
____
 F.  Put the airplane back to its usual condition.
 S 414-011
 (1)  Install the clamp around the electrical conduit and attach to the bracket of the left box assembly (Fig. 401, Sheet 1).
 S 094-017
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO REMOVE THE
_______ DOOR LOCKS FROM THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT REMOVE THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (2)  Do this task: "Removal of the Door Locks on the Nose Landing Gear" (Ref 32-00-30/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-21-07
 ALL  ú ú 01 Page 409 ú Oct 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 TOW FITTING - REMOVAL/INSTALLATION
__________________________________
 1.  General_______
 A. This procedure contains two tasks:
 (1)  
The removal of the tow fitting.

 (2)  
The installation of the tow fitting.

 TASK 32-21-08-004-001
 2.  Tow Fitting Removal (Fig. 401)___________________
 A. References
 (1)  
AMM 09-11-00/201, Towing

 (2)  
AMM 32-45-02/401, Nose Gear Tire and Wheel

 (3)  
AIPC 32-21-08 Fig. 1, AIPC 32-45-03

 B.
Access

 (1)  
Location Zone
 715 Nose Landing Gear

 C.
Procedure

 S 494-010
 (1)
Install the ground locks in all landing gear (AMM 09-11-00/201).

 S 034-003

 (2)  
If it is necessary, remove the nose wheel (AMM 32-45-02/401) on the opposite side of the pin nut of the tow fitting.

 S 024-004

 (3)  
Remove the nut, the washer, the pin and the tow fitting.

 TASK 32-21-08-404-005
 3.  Tow Fitting Installation (Fig. 401)________________________
 A. Consumable Materials
 (1)  
D00014 Grease - MIL-G-21164

 (2)  
G00009 Compound - Corrosion Inhibiting, BMS 3-23 (LPS-3)

 B.
References

 (1)  
AMM 09-11-00/201, Towing

 (2)  
AMM 32-45-02/401, Nose Gear Tire and Wheel

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-21-08
 ALL  ú ú 01 Page 401 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

747-400
MAINTENANCE MANUAL

FWD
SEE A
PIN
TOW FITTING (TYP)
COTTER PIN 
NUT 
A  WASHER 
Tow Fitting Figure 401 

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-21-08
 ALL  ú ú 01 Page 402 ú Jun 10/88
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (3)  
AIPC 32-21-08 Fig. 1, AIPC 32-45-03

 C.
Access

 (1)  
Location Zone
 715 Nose Landing Gear

 D.
Procedure

 S 494-011
 (1)
Install the ground locks in all landing gear (AMM 09-11-00/201).

 S 424-007

 (2)  
Install the tow fitting.

 (a)  
Apply a corrosion preventive compound to the tow fitting.

 (b)  
Apply a light layer of grease to the pin shank and the threads, the washer and the nut.

 (c)  
Set the tow fitting on the shock strut.

 (d)  
Install the attach pin, the washer and the nut.

 (e)  
Tighten the nut 50 - 70 pound-feet.

 (f)  
Loosen the nut to the nearest slot and install the cotter pin.

　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 3(156)