32-21-01
ALL ú ú 03 Page 406 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
SEE B
SEE A SEE D
TRUNNION
BEARING (2)
A
DRAG STRUT SEE E
SEE C
A
TRIPOD APEX
BULLNOSE
ASSEMBLY
CONNECTORS
D2694 A
D2693
COVER WALL OF THE
AFT WHEEL WELL
CONDUIT
CLAMP
B
Nose Gear Installation
Figure 402 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-21-01
ALL ú ú 01 Page 407 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
AFT DOOR OPERATOR ROD
BULKHEAD SUPPORT FITTING
DRIVE CRANK
TRUNNION BEARING CAP
BEARING CAP BOLTS
A 747-400 MAINTENANCE MANUAL
RETRACT ACTUATOR
ACTUATOR BOLT
TRUNNION CRANK ARM
TRUNNION
C
DRAG STRUT
UPPER DOWNLOCK LINK ASSEMBLY
GROUND LOCK
LOWER DOWNLOCK LINK ASSEMBLY
FWD D
Nose Gear Installation
Figure 402 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-21-01
ALL ú ú 01 Page 408 ú Oct 10/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
BODY SUPPORT
DO NOT APPLY SEALANT TO INSIDE SURFACE OF TRUNNION BUSHING ASSEMBLY
Nose Gear Installation Figure 402 (Sheet 3)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-21-01
ALL ú ú 01 Page 409 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 034-020
WARNING: MAKE SURE YOU HOLD THE TRIPOD BEFORE YOU REMOVE THE APEX PIN.
_______ THE TOP TRIPOD BRACE WEIGHS APPROXIMATELY 45 POUNDS. THE LOWER TRIPOD BRACE WEIGHS APPROXIMATELY 57 POUNDS. FAILURE TO HOLD THE TRIPOD WILL CAUSE THE TRIPOD TO FALL. IT CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(3)
Remove the tripod apex pin.
(a)
Remove the apex pin nut of the tripod.
(b)
Install the thread protector.
(c)
Adjust the forward caster jacks to release the pressure on the pin.
(d)
Remove the tripod apex pin.
(e)
Move the drag strut forward and insert the apex pin in the tripod assembly.
(f)
Hold the drag strut forward.
S 034-021
CAUTION: KEEP THE BEARINGS AND THE BEARING CAPS IN THE SETS.
_______ IF YOU USE THE INCORRECT SETS, YOU CAN CAUSE TOO MUCH WORN AREAS OR DAMAGE TO THE EQUIPMENT.
(4)
Remove the two bolts on each trunnion to remove the bearing caps from the trunnion fitting.
(a)
Make a mark on the bearings and the caps for installation.
NOTE: Remove each side of the door opening below the trunnion
____ bearings to get access to the cap nuts. Remove the exterior skin panel approximately 5-1/2 x 17 to get to the fairing fasteners.
S 024-022
(5)
Remove the nose landing gear.
(a)
Use the dolly caster jacks to lower the gear.
WARNING: LOCK THE OUTBOARD CASTER JACKS WHEN YOU MOVE THE NOSE
_______ LANDING GEAR. DO NOT TOW THE NOSE LANDING GEAR MORE THAN 3 MILES PER HOUR. KEEP THE RADIUS OF TURNS TO 10 FEET MINIMUM TO PREVENT THE GEAR TO FALL. MOVE THE NOSE GEAR WITH THE WHEELS ON WHEN YOU USE THE DOLLY.
(b) Use the dolly to move the nose landing gear from the area.
TASK 32-21-01-404-023
3. Nose Landing Gear Installation
______________________________
A. Special Tools and Equipment
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機(jī)維護(hù)手冊(cè) 起落架 LANDING GEAR 3(104)
