NUT
(REF)
HINGE  WING GEAR WHEEL WELL INBOARD DOOR
BUSHING FWD
WING GEAR WHEEL
WELL INBOARD DOOR FWD
B C
Wing Gear Wheel Well Inboard Door Installation
Figure 401

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-12-02
 ALL  ú ú 01 Page 402 ú Feb 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 494-028
 (3)  
Do this task: "Installation of the Door Locks on the Body Landing Gear" (AMM 32-00-30/201).

 S 034-005

 (4)  
Do this task: "Removal of the Outboard Door on the Wheel Well of the Wing Landing Gear" (AMM 32-12-01/401).

 E.  
Remove the Inboard Door on the Wheel Well

 (1)  S 034-006Disconnect the linkage rod from the inboard door.
 (2)  S 014-007Remove the strike board (AMM 32-12-03/401).
 (3)  S 034-008Disconnect the bonding jumpers from the inboard door.
 (4)  S 494-009Hold the door with the sling assembly.
 (5)  S 034-010Remove the hinge bolts on the inboard door of the wheel well.
 (6)  S 024-011Remove the inboard door on the wheel well of the wing landing gear.

 TASK 32-12-02-404-012
 3.  The Inboard Door Installation on the Wheel Well of the Wing Landing Gear________________________________________________________________________ (Fig. 401)
 A.  Special Tools and Equipment
 (1)  
OHME65B10910 - Sling Assembly

 B.  
Consumable Materials

 (1)  
D00091 Oil - General Purpose, Low, MIL-L-7870

 C.  
References

 (1)  
AMM 32-12-00/501, Wing Gear Doors

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-12-02
 ALL  ú ú 01 Page 403 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (2)  
AMM 32-12-01/401, Wing Gear Wheel Well Outboard Door

 (3)  
AMM 32-12-02/601, Wing Gear Wheel Well Inboard Door

 (4)  
AMM 32-12-03/401, Wing Gear Wheel Well Door Strike Board

 (5)  
AIPC 23-12-01 Fig. 2, AIPC 32-12-02 Fig. 2, AIPC 32-12-03 Fig. 1, AIPC 32-12-08 Fig 1

 (6)  
SWPM 20-20-00

 D.  
Access

 (1)  
Location Zone
 731 Wing Landing Gear Doors, LH
 741 Wing Landing Gear Doors, RH

 E.  
Prepare for the Installation

 S 224-013
 (1)  
Examine the attach fittings on the linkage rod of the inboard door hinges for worn areas (AMM 32-12-02/601).

 S 224-026

 (2)  
Examine the attach points on the strike board for worn areas (AMM 32-12-02/601).

 S 424-014

 (3)
Set the inboard door with the sling assembly for installation.

 F.  
Install the Inboard Door on the Wheel Well

 S 434-015
 (1)  
Install hinge bolts as shown on details A and B, Fig. 401.

 (a)
Put one washer between the bolt head and the hinge.

 1)  Put the necessary number of washers between the nut and the hinge.
 NOTE: The clearance between the nut and the hinge is 0.01
____ to 0.06 inch after you install the nut.
 (b)  
Turn the nut on the bolt the minimum distance necessary to install the cotter pin.

 (c)  
Make sure that the clearance between the nut and the washers is

 0.01 to 0.06 inch.
 (d)  Install the cotter pin.
 S 644-016
 (2)  
Apply a small quantity of MIL-L-7870 Oil to hinge bushings and clean it dry.

 S 434-017

 (3)
Connect the attach fitting of the linkage rod on the inboard door.

 (a)  
Install the bolt, bushing, washers, nut, and cotter pin.

 (b)  
Tighten the nut 600 to 1500 pound-inches.

 (4)  
Install the bonding jumper (SWPM 20-20-00).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 2(99)