FOR IN-SERVICE REPAIR, INSTALL SPECIAL SHIM (REF 32-00-01/801); PREFERRED OVERHAUL REWORK IS TO RESTORE PART TO DESIGN LIMITS SHOCK STRUT PART NUMBER 161U1500 OBTAIN REPLACEMENT BUSHING. INSTALL BUSHING PER 20-11-01 WITH INTERFERENCE FIT WORN PART IS REPAIRABLE. REFER TO OVERHAUL MANUAL FOR REPAIR INFORMATION DISTANCE BETWEEN BUSHING FLANGES DISTANCE OVER BUSHING FLANGES REPLACE WORN PART OR SHIM UNDER FLANGE OF EACH BUSHING 0.0150 INCH MAXIMUM LIMITS SHOWN MAY BE EXCEEDED PROVIDED MAXIMUM CLEARANCE IS NOT EXCEEDED MAXIMUM AXIAL CLEARANCE
Wing Landing Gear Torsion Links Wear Limits
Figure 601 (Sheet 3)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-14
ALL ú ú 01 Page 604 ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
WING GEAR WALKING BEAM - REMOVAL/INSTALLATION
_____________________________________________
1. General
_______
A. This procedure has two tasks:
(1)
The removal of the walking beam for the wing gear (referred to as the walking beam).
(2)
The installation of the walking beam.
B.
The walking beam is attached at two locations. The inboard end of the walking beam is attached to the top of the shock. The outboard end is attached to the walking beam support and the retract actuator. The removal and the installation procedures apply to the two walking beams.
TASK 32-11-15-004-001
2. Wing Gear Walking Beam Removal (Fig. 401)
______________________________
A. References
(1)
AMM 09-11-00/201, Towing
(2)
AMM 29-11-00/201, Main Hydraulic Supply System
(3)
AMM 32-00-30/201, Landing Gear Door Locks
(4)
AIPC 32-11-15 Fig. 2
B.
Access
(1)
Location Zone
735 Wing Landing Gear, LH
745 Wing Landing Gear, RH
C.
Procedure
S 864-020
WARNING: YOU MUST CAREFULLY INSTALL THE GROUND LOCKS IN ALL LANDING
_______ GEAR. AN ACCIDENTAL RETRACTION OF THE LANDING GEAR CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(1) Install the ground locks in all landing gear (AMM 09-11-00/201).
S 494-021
WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO INSTALL
_______ THE DOOR LOCKS ON THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT INSTALL THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(2) Do this task: "Installation of the Door Locks on the Wing Landing Gear" (AMM 32-00-30/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-15
ALL ú ú 01 Page 401 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
SEE A
6. WALKING BEAM
SUPPORT
SEE B
7. LOCKBOLT
9. BOLT
8. WASHER FWD
1. WALKING BEAM
10. RETRACT FWD
ACTUATOR
1. WALKING BEAM
A
5. SHOCK STRUT
4. LOCKBOLT
2.
BOLT
3.
WASHER
B
Walking Beam Installation for the Wing Landing Gear
Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-15
ALL ú ú 01 Page 402 ú Oct 10/91
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 2(21)
