(5)  
IPC 32-12-05 Fig. 1, 32-12-06

 B.
Access

 (1)  
Location Zone
 733 Wing Landing Gear Door, LH
 743 Wing Landing Gear Door, RH

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-12-06
 ALL  ú ú 01 Page 404 ú Jun 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 C.  Procedure
 S 224-013
 (1)  
Examine inboard door hinges and actuator rod attach points for allowable wear (Ref 32-12-06/601).

 S 224-029

 (2)  
Examine the inboard door hinge and the attach points of the actuator rod for permitted wear limits (Ref 32-12-06/601).

 S 214-014

 (3)  
Make sure you install the bushings in each hinge on the inboard door.

 S 434-015

 (4)  
Install the bushing in the hinge on the outboard door (Details B and C, Fig. 401).

 D.  
Install the Inboard Door of the Shock Strut (Fig. 401)

 S 424-016
 (1)  
Set the door for installation and install the hinge bolts (Details B and C, Fig. 401).

 S 434-017

 (2)
Tighten the nuts on the two small hinges 60 - 85 pound-inches.

 S 434-018

 (3)  
Tighten the nut on the large hinge 370 - 610 pound-inches.

 S 434-019

 (4)  
Clean and install the bonding jumper.

 S 434-020

 (5)  
Connect the linkage rod to the inboard door.

 (a)  
Measure the length and adjust the linkage rod if you replace it or if you change the length.

 NOTE: You must see the rod threads through the inspection hole
____
 of the linkage rod.

 1)  If the attach fitting of the inboard door is a bolt on (clevis type), do the step below: a) Adjust the rod to 21.50 inches measured from the center
 of each rod end.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-12-06
 ALL  ú ú 01 Page 405 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 2)  If the attach fitting of the inboard door is the integral clevis type, do the step below: a) Adjust the rod to 21.80 measured from the center of
 each rod end.
 S 434-021
 (6)  
Tighten the nut 290 - 410 pound-inches.

 E.  
Put the Airplane in its Usual Condition

 S 824-022
 (1)  
Do this task: "Wing Landing Gear Shock Strut Inboard Door
 Adjustment" (Ref 32-12-00/501).

 S 414-023

 (2)  
Do this task: "Wing Landing Gear Shock Strut Door Fairing
 Installation" (Ref 32-12-05/401).

 S 094-027
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO REMOVE THE
_______ DOOR LOCKS FROM THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT REMOVE THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (3)  
Do this task: "Removal of the Door Locks from the Wing Landing Gear" (Ref 32-00-30/201).

 S 094-030

 (4)  
Do this task: "Removal of the Door Locks from the Body Landing Gear" (Ref 32-00-30/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-12-06
 ALL  ú ú 01 Page 406 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 WING LANDING GEAR SHOCK STRUT INBOARD DOOR - INSPECTION/CHECK
_____________________________________________________________
 1.  General
_______
 A.  This procedure contains a task to examine the linkage rod assemblies and hinge assemblies of the inboard door for worn parts.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 2(109)