WEAR LIMITS
Walking Beam to Hanger Bolt Installation
Figure 201 (Sheet 2)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-16
 ALL  ú ú 01 Page 203 ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 492-026
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO INSTALL
_______ THE DOOR LOCKS ON THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT INSTALL THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (2)  
Do this task: "Installation of the Door Locks on the Wing Landing Gear" (AMM 32-00-30/201).

 S 492-027

 (3)  
Do this task: "Installation of the Door Locks on the Body Landing Gear" (AMM 32-00-30/201).

 S 842-004

 (4)  
Release the pressure from the hydraulic system No. 4
 (AMM 29-11-00/201).

 S 012-005

 (5)  
Lower the access panel for the trailing edge (571AB LH and 671AB RH) (AMM 06-09-08/201).

 D.
Procedure

 S 032-006
 (1)  
Remove the two halves of the walking beam for the wing landing gear (AMM 32-11-15/401).

 S 032-007

 (2)  
Remove the head end of the actuator from the bolt for the walking beam (AMM 32-32-01/401).

 S 032-008

 (3)  
Remove the walking beam support (hanger) with the bolt in the lugs of the support (AMM 32-11-18/401).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-16
 ALL  ú ú 01 Page 204 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 S 022-009
 (4)  Remove the bolt from the support.
 TASK 32-11-16-402-010
 3. Bolt For The Walking Beam Installation
_______________________________________
 A. Consumable Materials
 (1)  
D00633 Grease - BMS 3-33 (preferred)

 (2)  
D00013 Grease - MIL-G-23827 (optional)

 B.
References

 (1)  
AMM 06-09-08/201, Wing Access Doors and Panels

 (2)  
AMM 09-11-00/201, Towing

 (3)  
AMM 12-21-01/301, Landing Gear

 (4)  
AMM 32-00-30/201, Landing Gear Door Locks

 (5)  
AMM 32-11-15/401, Wing Gear Walking Beam

 (6)  
AMM 32-11-18/401, Walking Beam Support

 (7)  
AMM 32-32-01/401, Wing Gear Actuator

 (8)  
AIPC 32-11-15 Fig. 2

 C.
Access

 (1)  
Location Zone 571 Rear Spar to Landing Gear Support Beam, LH 671 Rear Spar to Landing Gear Support Beam, RH

 D.
Prepare for the Installation

 S 222-013
 (1)  
Examine the attached point for the approved worn areas (Ref Bolt For The Walking Beam Inspection).

 E.
Procedure

 S 422-014
 (1)
Set the bolt through the support lugs of the walking beam.

 S 432-015

 (2)  
Install the walking beam support (hanger) with the bolt through the support lugs (AMM 32-11-18/401).

 S 432-016

 (3)  
Install the head end of the actuator through the bolt (AMM 32-32-01/401).

 S 432-017

 (4)  
Install the walking beams on each side of the actuator (AMM 32-11-15/401).

 F.
Put the Airplane back to its usual condition.

 (1)  
Lubricate the bolt with the grease (AMM 12-21-01/301).

 S 642-018
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-16
 ALL  ú ú 03 Page 205 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 2(25)