(b)  
Remove the bolts (2 and 3) and the bonding jumpers.

 (c)  
Hold the fairing.

 (d)  
Remove the bolts (1).

 NOTE: You install the washer below the bolt (1) at the
____ forward edge of the fairing at the same location.
 (e)  Remove the door fairing.
 TASK 32-12-05-404-006
 3. Wing Gear Shock Strut Door Fairing Installation (Preferred Procedure)
_____________________________________________________________________ (Fig. 401)
__________
 A. References
 (1)  AMM 32-00-30/201, Landing Gear Door Locks
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-12-05
 ALL  ú ú 01 Page 403 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (2)  
AMM 32-12-00/501, Wing Gear Doors

 (3)  
AIPC 32-12-05 Fig. 1

 B.
Access

 (1)  
Location Zone
 733 Wing Landing Gear Door, LH
 743 Wing Landing Gear Door, RH

 C.
Procedure

 S 424-007
 (1)  
Install the door fairing.

 (a)  
Set the door fairing for the installation.

 (b)  
Install the bolts (1) with the washers.

 S 824-008
 (2)  Adjust the fairing (AMM 32-12-00/501).
 NOTE: You install the rivets (4), the bolts (2) and (3) and
____ the bonding jumper during the fairing adjustment.
 S 094-016
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO REMOVE THE
_______ DOOR LOCKS FROM THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT REMOVE THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (3)  
Do this task: "Removal of the Door Locks on the Wing Landing Gear." (AMM 32-00-30/201).

 S 944-022

 (4)  
Do this task: "Removal of the Door Locks on the Body Landing Gear." (AMM 32-00-30/201).

 TASK 32-12-05-324-023
 4. Wing Gear Shock Strut Door Fairing Installation (Alternate Procedure)
_____________________________________________________________________ (Fig. 401).
__________
 NOTE: The alternate installation procedure may be used when no related
____
 wing landing gear components have been removed or adjusted.

 A. Procedure
 S 424-024
 (1)  Position fairing at the location marked on the wing gear shock strut door. Install bolts (1) with washers.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-12-05
 ALL  ú ú 01 Page 404 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (2)  S 424-025Install the two rivets (4).
 (3)  S 424-026Install bolts (3) in the three center holes.  Clean bonding jumpers

 and install with bolts (2) in the two end holes. S 944-028 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO REMOVE THE
_______ DOOR LOCKS FROM THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT REMOVE THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (4) Remove wing and body gear door locks (AMM 32-00-30/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-12-05
 ALL  ú ú 01 Page 405 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 WING LANDING GEAR SHOCK STRUT INBOARD DOOR - REMOVAL/INSTALLATION
_________________________________________________________________
 1.  General_______
 A. This procedure contains two tasks:
 (1)  
The removal of the inboard door of the shock strut from the wing landing gear.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 2(107)