32-13-02
 ALL  ú ú 02 Page 204 ú Jun 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

747-400
MAINTENANCE MANUAL

SCRAPER
ASSEMBLY

SPLIT SCRAPER
(TEMPORARY REPLACEMENT ONLY)
A-A

Scraper Ring Installation for the Body Landing Gear
Figure 202

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-13-02
 ALL  ú ú 01 Page 205 ú Jun 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A39368
A
747-400 MAINTENANCE MANUAL
 TASK 32-13-02-402-005
 3. Body Landing Gear Shock Strut Pressure Gage Installation (Fig. 201)
________________________________________________________
 A. Consumable Materials
 (1)  
B00062 Solvent - O-A-51, Acetone

 (2)  
B00316 Solvent - TT-N-95, Type I

 B.
Parts

 ~.............................................................................. | MM | | IPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ |201 | 1 | Washer | 32-13-01 | 05 | 85 | | | 2 | Nut | | | 90 | | | 3 | Pressure Gage Assembly | | | 74 | | | 4 | Valve-Check | 32-13-01 | 05 | 70 | | | 5 | Cap | | | 65 | | | 6 | Packing (O-ring) | 32-21-01 | 04 | 40 | | | 7 | Flow Fuse Assembly (Flow Fuse) | 32-13-01 | 05 | 17 | | | 8 | Pin-Stop (pin) | | | 18 | | | 9 | Valve Assembly (shutoff valve) | 32-13-01 | 05 | 20 | 2......…........…...................................…..........….....….........1
 C. References
 (1)  
09-11-00/201, Towing

 (2)  
32-00-30/201, Landing Gear Door Locks

 D.
Access

 (1)  
Location Zone
 755 Body Landing Gear, LH
 765 Body Landing Gear, RH

 E.
Procedure

 S 962-061
 (1)  Remove the oil fill valve (4) and the pressure cap (5) from the removed pressure gage assembly (3).
 NOTE: Use these on the replacement assembly if a new oil fill valve
____ and a new pressure cap are not necessary.
 S 112-062
 (2)  
Clean the oil fill valve (4) with solvent.

 (a)  
Flush the oil fill valve (4) with acetone.

 (b)  
Make the valve dry with a clean cloth to remove all signs of the solvent.

 (c)  
Soak the O-ring in some of the hydraulic fluid for the shock strut.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-13-02
 ALL  ú ú 01 Page 206 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 432-066
 (3)  
Install the O-ring on the oil fill valve (4).

 S 432-067

 (4)  
Install the oil fill valve (4) with the pressure cap (5) on the pressure gage assembly (3).

 (a)  
Tighten the valve to 22-25 pound-inches.

 S 432-007
 (5)
Put the pressure gage assembly on the shock strut clamps.

 S 432-008

 (6)  
Install the four nuts (2) and washers (1).

 S 432-068

 (7)
Connect the hydraulic tube to the pressure gage assembly (3).

 S 432-069

 (8)  
Install a lockwire from the oil fill valve (4) to the tube connection.

 S 862-070

 (9)  
Slowly open the shutoff valve (9) with a 3/16-inch hex wrench.

 S 782-071

 (10)
 Make sure the pressure gage operates correctly.

 S 792-072

 (11)
 Make sure there is no leakage.

 F.
Put the Airplane back to its Usual Condition

 S 092-073
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASKS BELOW TO REMOVE
_______ THE DOOR LOCKS FROM THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT REMOVE THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (1)  
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 2(134)