0.60 +0.45/-0.20 INCH (15.24 +11.43/-5.08 mm)

D-D
+0.06/-O.25 INCH (+1.52/-6.35 mm)
0.58 +0.09/-0.28 INCH (14.73 +2.28/-7.11 mm)
Wing Gear Shock Strut Door Fairing Adjustment
Figure 507 (Sheet 2)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-12-00
 ALL  ú ú 19 Page 537 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 ~............................................................................... | WING GEAR SHOCK STRUT DOOR FAIRING FLUSHNESS AND CLEARANCE DEVIATIONS | | TABLE 504 | ................................................................................. | | | TYPE OF | MISMATCH | | | AIRPLANE | ZONE | MISMATCH | (FLUSHNESS) | CLEARANCE | 2............…........….............…..................…........................1
 S 865-097
 WARNING: MAKE SURE THAT ALL PERSONS AND EQUIPMENT ARE CLEAR OF THE DOOR
_______ OPERATION PATHS. DO NOT MOVE THE DOORS TOO QUICKLY. IT CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (2)  
Operate the release handle to open the wheel well doors for the wing and body landing gear.

 S 825-198

 (3)
Adjust the door fairing for the shock strut (Fig. 507 Sheet 2).

 (a)  
Loosen the bolts (1) on the fairing.

 (b)  
Adjust the door fairing to align with the body fairing in the tolerances. Add or remove shims if needed, between the inboard door and the fairing. (View A-A and B-B, Fig. 507). 1) Shim the forward and aft ends first. Shim gaps greater than

 .006 inch on remaining middle three frame stations.
 2)  The maximun shim thickness is .18 inch. Make the width and Length as needed to match the footprint of the fairing within t/- .05 inch.
 3)  Maintain a minimum edge margin of .50 inch on both
 fasteners at any frame station. 4) Fay surface seal between frames and each shim used. 5) Fillet seal gap between the fairing and the door.
 (c)  Tighten the bolts (1) to set the location of the door fairing.
 S 865-100
 (4)  Pressurize the hydraulic systems No. 1 and 4
 (AMM 29-11-00/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-12-00
 ALL  ú ú 21 Page 538 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

B

D-D

Wing Gear Shock Strut Door Fairing Adjustment
Figure 507 (Sheet 3)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-12-00
 ALL  ú ú 15 Page 539 ú Oct 10/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

SEE  A 
SUPPORT STRUCTURE 
HINGE FITTING 
B 
BOLT 
KEEL BEAM  LINK STABILITY 
A 
INBOARD DOOR WHEEL WELL WING GEAR  A 
FWD  OUTBD  OUTBOARD DOOR WHEEL WELL WING GEAR  A  STRIKE BOARD TRACK ASSEMBLY B 
Figure 508 (Sheet 1) Wing Gear Door Strike Board Rigging 

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-12-00
 ALL  ú ú 17 Page 540 ú Oct 10/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

UP

Wing Gear Door Strike Board Installation Figure 508 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 2(87)