32-11-07
 ALL  ú ú 01 Page 204 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 022-014
 (14) Remove the spindle from the airplane.
 TASK 32-11-07-402-015
 3.  Wing Gear Side Strut Lower Spindle Installation (Fig. 201)________________________________________________
 A. Standard Tools and Equipment
 (1)  
Thickness gage - commercially available

 B.
Consumable Materials

 (1)  
D00633 Grease - BMS 3-33 (preferred)

 (2)  
D00013 Grease - MIL-G-23827 (optional)

 C.
References

 (1)  
AMM 07-11-01/201, Jacking Airplane

 (2)  
AMM 09-11-00/201, Towing

 (3)  
AMM 32-00-30/201, Landing Gear Door Locks

 (4)  
AIPC 32-11-07 Fig. 2, AIPC 32-11-23 Fig. 1

 D.
Access

 (1)  
Location Zone
 735 Wing Landing Gear, LH
 745 Wing Landing Gear, RH

 E.
Procedure

 S 222-019
 (1)  
Examine the attach points for too much worn areas, Lower Spindle Inspection (AMM 32-11-07/201).

 S 432-020

 (2)  
Prepare the lubrication insert (7) for installation.

 (a)  
Examine the O-rings (8) on the lubrication insert (7) for worn areas or damage.

 NOTE: Replace them if it is necessary.
____
 (b)  
Apply a thick layer of grease on the O-rings (8), the lubrication insert (7), and the inner surface of the spindle bolt (9).

 (c)  
Move the O-rings (8) on the lubrication insert (7).

 (d)  
Lubricate the lubrication insert (7) if it is necessary.

 (e)  
Move the lubrication insert (7) and the O-rings (8) into the spindle bolt (9).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-07
 ALL  ú ú 01 Page 205 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (f)  Align the cross bolt holes to make the spindle pin assembly.
 S 162-021
 (3)  
Clean all bolts, the nuts, the washers, and the bushings immediately before the installation.

 S 642-022

 (4)  
Lubricate all bolts, the nuts, the washers, and the bushings immediately before the installation.

 F.
Procedure

 S 422-023
 (1)  Install the spindle, the washer (13), and the bracket (14).
 NOTE: hold them with the nut (15).
____
 S 432-024
 (2)  Tighten the nut (15) 600 to 1200 pound-inches.
 NOTE: Loosen the nut to the nearest castellation.
____
 S 432-025
 (3)
Install the spring housing (12) and hold it with the pins (16).

 (a)  
Install the cotter pins.

 S 432-026
 (4)  
Install the spring (19) and the pushrod assembly (11) through the spindle from the lower side.

 S 432-027

 (5)  
Install the locknut, the locking washer and the rod end (17) temporarily on the top end of the pushrod.

 NOTE: You make the pushrod connection and the truck lock
____
 adjustments after the installation.

 S 432-028
 (6)
Hold the frame (20) to the bracket (14) with the bolt and the nut.

 S 822-029

 (7)  
Keep the parallelism of the planes D and E (bracket and frame) within 0.005 inch.

 S 222-055

 (8)  
Measure the clearance and the shim to prepare before the last installation of the bolt (22).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-07
 ALL  ú ú 01 Page 206 ú Jun 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 S 432-030
 (9)  
Install the shim (21) and the bolt (22).

 S 432-056
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 1(145)